SS-CE-501Dh-A

概 要 GENERAL

501D 系列调节阀采用了多级降压式套筒完全控制了流经阀内件的流体流速故可大幅度降低高压差气体或蒸汽所产生的噪音也可有效防止液体产生气蚀现象是一种无气蚀损伤低噪音控制流体稳定的经济型调节阀 The Series 501D valves are engineered specifically for critical anti-cavitation and low noise applications on liquids, gases or steam. Multi-stage cage controls flowing velocities in the valve trim by forcing the process fluid to follow a tortuous path of right-angle turns. The resistance to flow

provided by these turns reduces fluid velocities

significantly. Therefore, a vena contracta is never formed in

the trim and noise and cavitation are stopped before they

can start.

标准规格 STANDARD SPECIFICATIONS

本体部 BODY 形式 Type

流体压力平衡型阀芯 Pressure balanced plug type

公称通径 Body size 1"12"25A 300A 即DN25DN300

阀芯形状 Plug form 流体压力平衡型阀芯 Pressure balanced plug type

流量特性 Characteristics 线性

改良线性改良等百分比 Linear , Modified Linear , Modified EQ%

阀内件材质 阀内件处理 Trim materials Trim treatment

标准材质组合及使用温度请参见表1

See Tables 1 for hardening treatment and operating temperature. 公称压力 Body rating

ANSI Class 9001500 2500

连接方式 Body connections 法兰型RF RTJ 焊接型SW BW

Flanged RF RTJ Weld ends SW BW

法兰距 Face to Face dimension 请参见第1726页

See pages 1726.

阀体及 上阀盖材质 Body & Bonnet Material SCPH2/WCB, SCPH21/WC6, SCPH32/WC9, SCPL1/LCB, SCS13A/CF8,

SCS14A /CF8M

各种材质的使用温度压力范围请参见表1表2

As to the operating pressure-temperature limitation for each material, see Tables 1

and 2.

上阀盖形式 Bonnet type 标准型 Standard type : 5230

散热片型 Fin-Extension type : 455或者超过230的场合

45under 5 or over 230

加长型 Long-Extension type : 195

但必须注意各材质的使用温度压力范围

Note : The allowable operating pressure-temperature limitation for each material. 填料 Packing

聚四氟乙烯碳纤维柔性石墨

各种填料的使用温度压力范围请参见图3

Teflon carbon fiber, Grafoil, See Fig. 3 for selection. 垫圈 Gasket

缠绕式垫圈聚四氟乙烯SUS316柔性石墨SUS316

各种垫圈的使用温度压力范围请参见图4

Spiral wound metal, with Grafoil or Teflon filler. See Fig. 4 for selection. 表面涂层色 Painting color

银灰色环氧树脂但是阀体材质为不锈钢时本体部不加涂层

Munsell N-6Epoxy resin group is standard. In the case of stainless steel body, no

Air supply

200 ) KPa G 300500 KPa G

650 )

随输入定位器信号增加阀开或阀闭

1% of FS with positioner

带定位器

1% of FS with positioner

2% FS

2% of FS with positioner 2% of FS with positioner

Standard type1070

High Temp.service 100

Low Temp. service 4040

Standard type2060

High Temp.service 0100

Low Temp. service 5060

P/P过滤减压阀电磁阀限位开关调速器锁止阀

P/P-Positioner,Air-set, Solenoid valve, Limit switch, Speed controller, Lock valve, Lock-up valve,

性能PERFORMANCE

额定C v值Rated Cv 请参见表3See Table 3.

流量特性Flow characteristics 线性改良线性改良等百分比Linear , Mod. Linear , Mod. EQ%

可调比R Rangeability 请参见表3See Table 3.

阀座泄漏量Seat Leakage 请参见表1See Table 1.

允许压差Allowable pressure drops 请参见表4See Table 4.

特殊规格有偿OPTIONAL SPECIAL SPECIFICATIONS (Additional cost is required)

本体部特殊检查

Special testing for body

材料检查{液体渗透探伤检查PT放射线检查RT}流量特性检查低温试验

蒸汽试验

Material certificate, Liquid penetrant testing, Radiographic testing,

Flow characteristic testing, Low temperature testing, Steam testing.

本体部特殊清洗

Special cleaning for body

完全禁油除水处理

Oxygen clean, Oil-free, Water-free

本体部及执行机构特殊规格

Special specification for

body and actuator

防砂防尘型防盐腐蚀型寒冷地区用热带地区用无铜处理特殊空气配管及特殊

气接头真空工作条件用接触大气部分的螺栓螺母采用不锈钢指定涂层色

Sand and Dust proof, Salty environment proof, Cold area proof, Tropical area proof

Copper-free alloy, Special piping and fitting, Vacuum service proof,

SUS bolt and nut for exposed parts, Non-standard painting.表1 阀体阀内件材质组合及使用温度范围阀座允许泄漏量

Table 1 BODY/TRIM STANDARD MATERIAL COMBINATION, OPERATING TEMPERATURE AND SEAT LEAKAGE.

当阀座泄漏率要达到ANSI CLASS 时请与KOSO确认

When ANSI CLASS for seat leakage is required, please consult us.

R.TFE : 强化聚四氟乙烯 Reinforced Teflon SS : 部分堆焊司太莱合金Stellite seat surface

Hcr : 镀硬铬Hard chrome plated SF : 全部堆焊司太莱合金Stellite full surface

HT : 热处理 Heat

treatment

表1-1阀体材质碳钢

Table 1-1 BODY MATERIAL : CARBON STEEL

阀体材质Body material SCPH2/A216-WCB, SCPH21/A217-WC6, SCPH32/A217-WC9, SCPL1/A352-LCB 材质 Material410SS 410SS 410SS 718 Inconel

多级降压式套筒

Multi-stage Cage 处理 Treatment HT HT HT

材质 Material SUS410 SUS410 SUS410 A182-F11 阀芯

Plug 处理 Treatment HT HT HT SF 材质 Material SUS316 SUS410 SUS410 A182-F11 阀座

Seat ring 处理 Treatment R.TFE HT HT SS 材质 Material R.TFE R.TFE

柔性石墨 Grafoil 柔性石墨 Grafoil

平衡密封环

Balance seal 垫环 Back ring SUS316SUS316

垫圈 Gasket 材质 Material T/#1806GR T/#1806GR T/#1806GR T/#1806GR ANSI Class Class Class Class

阀座允许泄漏量

Seat Leakage Rated Cv微气泡级bubble-tight0.01% 0.01% 0.01%

SCPH2/WCB body 5200 5230 5425 5425

SCPH21/WC6 body SCPH32/WC9 body 5200 5230 5425 5565

使用温度

Operating

temperature

SCPL1/LCB body 452004523045350

表1-2 阀体材质不锈钢

Table 1-2 BODY MATERIAL : STAINLESS STEEL

阀体材质Body material SCS13A/A351-CF8, SCS14A/A351-CF8M

材质 Material SUS316 SUS316 SUS316 SUS316 多级降压式套筒

Multi-stage Cage 处理 Treatment

材质 Material SUS316 SUS316 SUS316 SUS316 阀芯

Plug 处理 Treatment Hcr Hcr+SS Hcr+SS SF 材质 Material SUS316 SUS316 SUS316 SUS316 阀座

Seat ring 处理 Treatment R.TFE SS SS SS

材质 Material R.TFE R.TFE*柔性石墨 Grafoil 柔性石墨 Grafoil

平衡密封环

Balance seal 垫环 Back ring SUS316SUS316

垫圈 Gasket 材质 Material T/#1806GR/T/#9090 T/#1806GR/T/#9090 T/#1806GR T/#1806GR ANSI Class Class Class Class

阀座允许泄漏量

Seat Leakage Rated Cv微气泡级bubble-tight0.01% 0.01% 0.01%

使用温度Operating Temp. 75200196230196565196565

*流体温度在75以下的场合平衡密封环的材质Fluoroloy G ; 垫环材质Elgiloy

When the fluid temperature is below 75, the materials for the balance seal and the back ring will be Fluoroloy G and Elgiloy, respectively.Table 2 BODY MATERIAL/OPERATING PRESSURE-TEMPERATURE RATING UNIT : MPa G

ANSI Class 900 ANSI Class 1500 ANSI Class 2500

温度

Temp. SCPL1

LCB

SCPH2

A105

WCB

SCPH21

F11

WC6

SCPH32

F22

WC9

SCS13A

F304

CF8

SCS14A

F316

CF8M

SCPL1

LCB

SCPH2

A105

WCB

SCPH21

F11

WC6

SCPH32

F22

WC9

SCS13A

F304

CF8

SCS14A

F316

CF8M

SCPL1

LCB

SCPH2

A105

WCB

SCPH21

F11

WC6

SCPH32

F22

WC9

SCS13A

F304

CF8

SCS14A

F316

CF8M

-196~38 14.88 14.88 24.79 24.79 41.33 41.34

-45~38 14.35 14.88 14.88 23.92 24.79 24.79 39.87 41.33 41.34 -5~38 14.35 15.31 15.50 15.50 14.88 14.88 23.92 25.51 25.84 25.84 24.79 24.79 39.87 42.52 43.07 43.07 41.33 41.34

50 14.18 15.01 15.33 15.35 14.34 14.43 23. 25.02 25.55 25.58 23.90 24.04 39.40 41.70 42.59 42. 39.84 40.07

100 13.52 13.90 14.62 14.70 12.25 12.65 22.53 23.16 24.36 24.50 20.42 21.09 37.56 38.62 40.61 40.85 34.01 35.14 150 13.18 13.56 13.90 13.98 10. 11.54 21.96 22.60 23.18 23.30 18.16 19.24 36.60 37.66 38.61 38.84 30.26 32.07 200 12.79 13.14 13.63 13.45 9.82 10.69 21.32 21. 22.73 22.40 16.37 17.83 35.53 36.50 37.88 37.35 27.28 29.71 250 12.17 12.51 13.33 13.26 9.15 10.02 20.28 20.84 22.22 22.10 15.26 16.68 33.80 34.75 37.03 36.83 25.43 27.80 300 11.30 11.61 12.72 12.72 8.71 9.49 18.84 19.36 21.20 21.20 14.52 15.80 31.40 32.26 35.33 35.33 24.20 26.34 350 10.78 11.08 12.06 12.06 8.42 9.12 17.96 18.46 20.11 20.11 14.02 15.20 29.95 30.78 33.51 33.51 23.36 25.36 375 10.94 11.63 11.63 8.32 8.91 18.22 19.38 19.38 13.86 14.84 30.37 32.32 32.32 23.12 24.74 400 10.34 10.98 10.98 8.23 8.72 17.24 18.28 18.28 13.72 14.55 28.73 30.47 30.47 22.87 24.25 425 8.62 10.53 10.53 8.14 8.59 14.37 17.54 17.54 13.57 14.32 23.94 29.23 29.23 22.63 23.87 450 6.01 10.13 10.13 8.06 8.42 10.02 16. 16. 13.42 14.03 16.68 28.16 28.16 22.37 23.38 475 4.06 9.50 9.50 7.97 8.20 6.76 15.82 15.82 13.27 13.67 11.28 26.36 26.36 22.13 22.79 500 8.33 8.33 7.81 8.05 13. 13. 13.02 13.40 23.15 23.15 21.71 22.34 525 6.08 6.58 7.15 7.73 10.12 10.96 11.94 12. 16.88 18.26 19.88 21.47 550 3.83 4.91 6.54 7.49 6.38 8.17 10.91 12.48 10.63 13.63 18.17 20.79 575 2.55 3.51 6.02 7.22 4.24 5.85 10.04 12.04 7.08 9.74 16.72 20.07 600 1.75 2.29 5.01 6.43 2.94 3.82 8.35 10.71 4.90 6.36 13.92 17.85 625 3.92

5.48

6.54

9.12

10.

15.20

650 3.16

4.23

5.25

7.06

8.75

11.76

675 2.33

3.78

3.88

6.31

6.45

10.53

图1软阀座使用温度压力范围

Fig. 1 SOFT SEAT OPERATING PRESSURE-TEMPERATURE RATINGSFig. 2 BALANCE SEAL OPERATING PRESSURE-TEMPERATURE RATINGS 图2-1 R.TFE/SUS316 图2-2 柔性石墨

Fig. 2-1 R.TFE/SUS316 Fig. 2-2 GRAFOIL

图2-3 FLUOROLOY G/ELGILOY

Fig. 2-3 FLUOROLOY G/ELGILOY

图3填料使用温度压力范围

Fig. 3 GLAND PACKING PRESSURE-TEMPERATURE RATINGS

图3-1 聚四氟乙烯碳纤维(P6528+P4519) 图3-2 柔性石墨(P6710CH+P6616CH) Fig. 3-1 TEFLON CARBON FIBER Fig. 3-2 GRAFOIL

图4垫圈使用温度压力范围

Fig. 4 GASKET OPERATING PRESSURE-TEMPERATURE RATINGS

图4-1 柔性石墨SUS316 (T/#1806GR) 图4-2 聚四氟乙烯SUS316 (T/#9090)

Fig. 4-1 GRAFOIL/SUS316 Fig. 4-2 TEFLON/ SUS316

表3额定Cv及行程

Table 3 Cv VALUE AND STROKE

表3-1 公称压力ANSI Class 9001500

多级降压式套筒的降压级数18级多级降压式套筒的材质410SS/SUS316

Table 3-1 BODY RATING ANSI Class 9001500

Multi-stage Cage Pressure Drop Levels : 18 Levels ; Multi-stage Cage Material : 410SS/SUS316

套筒材质410SS Cage material : 410SS

套筒材质SUS316 Cage material : SUS316

公称通径Valve size inch (mm)

阀芯尺寸

Plug size

inch (mm)

行程

Stroke

mm

最小可控

Min.Cv

1 lev

2 lev 4 lev 6 lev 8 lev 1 lev 2 lev 4 lev 6 lev 8 lev

1 (25) 5/8 (16) Standard

20 0.22 6.0 5.0 4.2 3.5 2.6 5.8 4.7 3.8 3.2 2.4 1.5(40) 1 (25) Standard

20 0.48 17.0 11.8 9.2 7.4 5.2 16.0 10.8 8.3 6.7 4.6

2 (50) 1.25 (32) Standard 25 0.67 29.2 15.

3 13.1 10.7 8.

4 28.0 13.7 11.6 9.6 6.8

3 (80) 2 (50) Standard 30 1.30 70.0 49.0 40.5 33.0 23.9 70.0 49.0 41.0 33.0 24.0

4 (100) 2.

5 (65) Standard 40 1.70 107.0 70.0 58.0 50.0 38.0 103.0 66.0 54.0 47.0 35.0

6 (150) 4 (100) Standard 50 3.30 258.0 145.0 115.0 97.0 77.0 256.0 143.0 114.0 94.0 75.0

8 (200) 5 (125) Standard 60 5.30 350.0 202.0 165.0 135.0 106.0 350.0 196.0 161.0 131.0 103.0 10 (250) 7 (175) Standard 80 6.90 580.0 345.0 283.0 231.0 182.0 580.0 330.0 271.0 221.0 173.0 12 (300) 8 (200) Standard 90 7.80 760.0 442.0 362.0 296.0 233.0 760.0 423.0 347.0 283.0 222.0

表3-2 公称压力ANSI Class 2500

多级降压式套筒的降压级数18级多级降压式套筒的材质410SS/SUS316

Table 3-2 BODY RATING ANSI Class 2500

Multi-stage Cage Pressure Drop Levels : 18 Levels ; Multi-stage Cage Material : 410SS/SUS316

套筒材质410SS Cage material : 410SS

套筒材质SUS316 Cage material : SUS316

公称通径Valve size inch (mm)

阀芯尺寸

Plug size

inch (mm)

行程

Stroke

mm

最小可控

Min.Cv

1 lev

2 lev 4 lev 6 lev 8 lev 1 lev 2 lev 4 lev 6 lev 8 lev

1 (25) 5/8 (16) Standard

20 0.22 6.0 5.0 4.2 3.5 2.6 5.8 4.7 3.8 3.2 2.4 1.5(40) 5/8

(16) Standard

20 0.22 6.0 5.0 4.2 3.5 2.6 5.8 4.7 3.8 3.2 2.4

2 (50) 1 (25) Standard 25 0.48 17.0 14.0 11.4 10.0 6.8 16.0 13.4 10.8 9.1 6.5

3 (80) 1.5 (40) Standard 30 0.86 45.0 23.0 20.0 16.0 13.0 44.0 22.0 19.0 15.0 12.0

4 (100) 2 (50) Standard 40 1.30 70.0 60.0 53.0 45.0 34.0 70.0 60.0 52.0 44.0 33.0

6 (150) 3 (80) Standard 50 2.20 153.0 104.0 86.0 75.0 57.0 152.0 102.0 85.0 74.0 56.0

8 (200) 4 (100) Standard 60 3.30 258.0 170.0 140.0 120.0 98.0 256.0 167.0 136.0 117.0 95.0

表3-3 公称压力ANSI Class 9001500

多级降压式套筒的降压级数 1024级多级降压式套筒的材质 410SS

Table 3-3 BODY RATING ANSI Class 9001500

Multi-stage Cage Pressure Drop Levels : 1024 Levels ; Multi-stage Cage Material : 410SS

流向 低进高出 Flow direction : Under Plug Flow 流向 高进低出 Flow direction : Over Plug Flow 公称通径 Valve size inch (mm) 阀芯尺寸 Plug size inch (mm) 行程 Stroke

mm 最小可控 Min.Cv 10 lev 12 lev 16 lev 20 lev 24 lev 10 lev 12 lev 16 lev 20 lev 24 lev

2.80 2.80

5/8 (16) Standard 20 0.10 2.10 2.10

1.70 1.70

Standard 20 1.10 1.10

1 (25) 1/

2 (15) Standard 12 0.04 0.66 0.66

2.80 2.80

5/8 (16) Standard 20 0.10 2.10 2.10

1.70 1.70

Standard 20 1.10 1.10

1.5 (40) 1/2 (15) Standard 12 0.04 0. 0.

1 (25) Standard 25 0.28 7.3 5.1

2 (50) 5/8 (16) Standard 25 0.10 3.

3 2.3

Standard 30 15.2 11.2 11.6 6.8

1.5 (40) Special 40 0. 20.8 15.5 16.1 9.5

Standard 30 7.6 3.6

3 (80) 1 (25) Special 40 0.28 10.2 5.1

Standard 40 28.3 22.0

2.5 (65) Special 50 1.36 35.0 27.3

Standard 40 19.8 12.7

2 (50) Special 50 0.94 24.5 15.8

Standard 40 14.4 10.0 8.1 4.1

4 (100) 1.2

5 (32) Special 50 0.3

6 17.3 12.2 10.0 5.1

Standard 50 75.1 52.7 54.8 35.4

4 (100) Special 70 3.17 102.6 72.9 75.7 49.2

Standard 50 39.7 23.0

3 (80) Special 70 2.01 54.5 32.0

Standard 50 25.4 12.8

6 (150) 2.5 (65) Special 70 1.36 34.9 17.9

Standard 60 122.0 84.1 65.3 44.5 101.0 63.5 44.9 27.5

8 (200) 5 (125) Special 80 4.50 159.0 111.0 86.5 59.2 133.0 84.1 59.7 36.6

Standard 80 174.0 122.0 96.5 146.0 94.2 .6

7 (175) Special 90 6.67 194.0 137.0 108.0 163.0 106.0 72.6

Standard 80 63.7 41.1

10 (250) 5 (125) Special 90 4.50 71.5 46.2

Standard 90 238.0 163.0 129.0 87.4 207.0 132.0 93.3 61.8

12 (300) 8 (200) Special 100 7.59 263.0 181.0 143.0 97.1 229.0 147.0 104.0 68.7

表3-4 公称压力ANSI Class 2500

多级降压式套筒的降压级数 1024级多级降压式套筒的材质 410SS

Table 3-4 BODY RATING ANSI Class 2500

Multi-stage Cage Pressure Drop Levels : 1024 Levels ; Multi-stage Cage Material : 410SS

流向 低进高出 Flow direction : Under Plug Flow 流向 高进低出 Flow direction : Over Plug Flow 公称通径 Valve size inch (mm) 阀芯尺寸 Plug size inch (mm) 行程 Stroke mm 最小可控

Min.Cv 10 lev 12 lev 16 lev 20 lev 24 lev 10 lev 12 lev 16 lev 20 lev 24 lev

2.80 2.80

5/8 (16) Standard 20 0.10 2.10 2.10

1.70 1.70

Standard 20 1.10 1.10

1 (25) 1/

2 (15) Standard 12 0.04 0.66 0.66

2.80 2.80

5/8 (16) Standard 20 0.10 2.10 2.10

1.70 1.70

Standard 20 1.10 1.10

1.5 (40) 1/2 (15) Standard 12 0.04 0. 0.

1 (25) Standard 25 0.28 7.3 5.1

2 (50) 5/8 (16) Standard 25 0.10 3.

3 2.3 Standard 30 10.

4 8.4 8.1 4.4

1 (25) Special 40 0.28 13.3 11.1 10.7 6.2

Standard 30 3.0 2.1

3 (80) 5/8 (16) Special 40 0.10 3.9 2.8

Standard 40 26.6 18.8 19.6 11.7

2 (50) Special 50 0.94 32.5 23.

3 24.2 14.5

Standard 40 14.2 7.8

1.5 (40) Special 50 0. 17.4 9.7

Standard 40 8.6 3.1

4 (100) 1 (25) Special 50 0.28 10.3 3.8

Standard 50 59.0 45.1

3 (80) Special 70 2.01 79.3 61.6

Standard 50 40.1 30.1 25.6 14.3

2 (50) Special 70 0.94 51.7 40.2 34.7 19.8

Standard 50 19.6 7.0

6 (150) 1.25 (32) Special 70 0.36 24.4 9.7

Standard 60 .1 62.9 68.8 42.3

4 (100) Special 80 3.17 116.0 82.6 90.2 56.1

Standard 60 47.2 27.5

3 (80) Special 80 2.01 61.6 36.4

Standard 60 29.4 13.6

8 (200) 2 (50) Special 80 0.94 37.7 18.0

表3-5 公称压力ANSI Class 9001500

多级降压式套筒的降压级数 1024级多级降压式套筒的材质 SUS316

Table 3-5 BODY RATING ANSI Class 9001500

Multi-stage Cage Pressure Drop Levels : 1024 Levels ; Multi-stage Cage Material : SUS316

流向 低进高出 Flow direction : Under Plug Flow 流向 高进低出 Flow direction : Over Plug Flow 公称通径 Valve size inch (mm) 阀芯尺寸 Plug size inch (mm) 行程 Stroke

mm 最小可控 Min.Cv 10 lev 12 lev 16 lev 20 lev 24 lev 10 lev 12 lev 16 lev 20 lev 24 lev

2.50 2.50

5/8 (16) Standard 20 0.10 1.90 1.90

1.60 1.60

Standard 20 0.98 0.98

1 (25) 1/

2 (15) Standard 12 0.04 0.59 0.59

2.50 2.50

5/8 (16) Standard 20 0.10 1.90 1.90

1.50 1.50

Standard 20 0.95 0.95

1.5 (40) 1/2 (15) Standard 12 0.04 0.57 0.57

1 (25) Standard 25 0.28 7.1 4.9

2 (50) 5/8 (16) Standard 25 0.10 3.2 2.3

Standard 30 15.2 11.1 11.6 6.8

1.5 (40) Special 40 0. 19.6 14.5 15.0 8.9

Standard 30 7.6 3.6

3 (80) 1 (25) Special 40 0.28 9.6 4.7

Standard 40 26.4 20.5

2.5 (65) Special 50 1.36 32.5 25.3

Standard 40 18.5 11.9

2 (50) Special 50 0.94 22.8 14.6

Standard 40 13.6 9.3 7.6 3.8

4 (100) 1.2

5 (32) Special 50 0.3

6 16.3 11.4 9.3 4.7

Standard 50 73.9 51.8 53.9 34.8

4 (100) Special 70 3.17 104.0 73.

5 76.4 49.7

Standard 50 39.1 22.6

3 (80) Special 70 2.01 55.0 32.3

Standard 50 25.0 12.6

6 (150) 2.5 (65) Special 70 1.36 35.3 18.1

Standard 60 119.0 81.9 63.6 43.4 98.9 61.8 43.7 26.7

8 (200) 5 (125) Special 80 4.50 159.0 111.0 86.4 59.2 133.0 84.0 59.6 36.6

Standard 80 174.0 122.0 96.4 146.0 94.1 .5

7 (175) Special 90 6.67 193.0 136.0 107.0 162.0 105.0 71.9

Standard 80 63.6 41.1

10 (250) 5 (125) Special 90 4.50 70.8 45.8

Standard 90 236.0 162.0 128.0 86.6 205.0 131.0 92.4 61.3

12 (300) 8 (200) Special 100 7.59 259.0 178.0 141.0 95.5 225.0 145.0 102.0 67.6

表3-6 公称压力ANSI Class 2500

多级降压式套筒的降压级数 1024级多级降压式套筒的材质 SUS316

Table 3-6 BODY RATING ANSI Class 2500

Multi-stage Cage Pressure Drop Levels : 1024 Levels ; Multi-stage Cage Material : SUS316

流向 低进高出 Flow direction : Under Plug Flow 流向 高进低出

Flow direction : Over Plug Flow 公称通径 Valve size inch (mm) 阀芯尺寸 Plug size inch (mm) 行程 Stroke mm 最小可控 Min.Cv 10 lev 12 lev 16 lev 20 lev 24 lev 10 lev 12 lev 16 lev 20 lev 24 lev

2.50 2.50

5/8 (16) Standard 20 0.10 1.90 1.90

1.60 1.60

Standard 20 0.98 0.98

1 (25) 1/

2 (15) Standard 12 0.04 0.59 0.59

2.50 2.50

5/8 (16) Standard 20 0.10 1.90 1.90

1.50 1.50

Standard 20 0.95 0.95

1.5 (40) 1/2 (15) Standard 12 0.04 0.57 0.57

1 (25) Standard 25 0.28 7.1 4.9

2 (50) 5/8 (16) Standard 25 0.10 3.2 2.

3 Standard 30 10.

4 8.4 8.1 4.4

1 (25) Special 40 0.28 12.7 10.5 10.1 5.8

Standard 30 3.0 2.1

3 (80) 5/8 (16) Special 40 0.10 3.7 2.7

Standard 40 24.9 17.6 18.3 10.9

2 (50) Special 50 0.94 30.4 21.6 22.4 13.4

Standard 40 13.3 7.2

1.5 (40) Special 50 0. 16.2 8.9

Standard 40 8.1 2.9

4 (100) 1 (25) Special 50 0.28 9.7 3.5

Standard 50 58.1 44.4

3 (80) Special 70 2.01 80.0 62.2

Standard 50 39.6 29.7 25.3 14.1

2 (50) Special 70 0.94 52.1 40.5 35.0 20.0

Standard 50 19.3 6.90

6 (150) 1.25 (32) Special 70 0.36 24.5 9.80

Standard 60 86.9 61.2 67.1 41.2

4 (100) Special 80 3.17 115.0 82.6 90.1 56.0

Standard 60 46.0 26.8

3 (80) Special 80 2.01 61.6 36.4

Standard 60 28.7 13.3

8 (200) 2 (50) Special 80 0.94 37.7 18.0

备 注 : 也可选用上表以外的降压级数及额定Cv 值请向KOSO 咨询

建议尽量选用1.5"(40A)以上的阀门口径从而避免选用1"(25A)口径

Remarks : Pressure drop levels and rated Cv are optional , please consult KOSO.

Suggest to choose 1.5" (40A) and above valve size , in order to avoid selecting 1" (25A).

图5 本体部构造

Fig. 5 BODY SECTION VIEW

填料压板 Gland flange 防尘圈 Wiper 填料压盖 Gland ring

填料 Gland packing 上阀盖 Bonnet 垫圈 P/B gasket 上阀盖垫圈 Bonnet gasket 平衡缸 Balance cylinder 平衡密封环 Balance seal 多级降压式套筒

Multi-stage cage 高进低出(液体) Over plug flow (Liquid) 阀杆

Stem

压板螺柱

Gland stud bolt 六角螺母

Nut

填料隔套 Lantern ring 填料座 Packing seat 阀体螺柱 Body stud bolt

六角螺母 Nut

阀芯

Plug

阀座 Seat ring

低进高出(蒸汽及气体)

Under plug flow

(Steam or Gas)

阀座垫圈

Seat gasket

阀体

Body

表4

最大允许压差

单位

MPa

Table 4 ALLOWABLE PRESSURE DROPS (UNIT : MPa ) 阀门口径与执行机构的标准组合请参见第1726页

See pages 1726, for valve size-actuator size combinations.

DA : 正作用

气压增加时阀闭 Direct action ( Air to valve shut ) RA : 反作用

气压增加时阀开 Reverse action ( Air to valve open )

表4-1 薄膜式执行机构

5200LA

Table 4-1 DIAPHRAGM ACTUATOR(5200LA)

表4-1A 填料 聚四氟乙烯碳纤维 (P6528+P4519)介质温度

+230以下

Table 4-1A PACKING : TEFLON CARBON FIBER/MEDIUM TEMPERATURE : UNDER +230

平衡密封环强化聚四氟乙烯SUS316

Balance seal : Reinforced Teflon/SUS316

阀芯尺寸

Plug size ( inch )

公称压力 Body rating 执行机构

尺 寸

Actuator size

气源压力

Air supply

(不平衡)

(Off-balance) KPa G 阀座形式 Seat ring

1/2 5/8 1 1.25 1.5 2 2.5 3 4 5 7 8

金属密封 18.30 17.70 16.80 16.40 14.80 10.90

350 300 (80)

软密封 10.19 10.19 10.19 10.19 10.19 10.19 金属密封 23.90 25.50 22.60 22.30 20.90 20.30 19.70 15.80 11.20

450 300 (80)

软密封 10.19 10.19 10.19 10.19 10.19 10.19 10.19 10.19 10.19 金属密封 24.80 23.80 23.40 23.00 22.30 21.70 16.80 14.10

ANSI Class 9001500

650 300 (80)

软密封 10.19 10.19 10.19 10.19 10.19 10.19 10.19 10.19 金属密封 18.30 17.70 16.80

14.80

350 300 (80)

软密封 10.19 10.19 10.19 10.19 金属密封 23.90 35.70 22.60 22.30 20.90 20.30

15.80 11.20 450 300 (80)

软密封 10.19 10.19 10.19 10.19 10.19 10.19 10.19 10.19 金属密封 24.80 24.10 23.80

23.00 22.30 ANSI Class 2500

650 300 (80)

软密封 10.19 10.19 10.19 10.19 10.19

表4-1B 填料 柔性石墨(P6710CH+P6616CH)介质温度

196565 Table 4-1B PACKING : GRAFOIL/MEDIUM TEMPERATURE : 196

565

平衡密封环柔性石墨

Balance seal : GRAFOIL

阀芯尺寸 Plug size ( inch )

公称压力

Body rating

执行机构

尺 寸

Actuator size

气源压力

Air supply

(不平衡)

(Off-balance) KPa G 阀座形式

Seat ring

1/2 5/8 1 1.25 1.5 2 2.5 3 4 5 7 8

350 11.50

450 17.20 17.20 14.20 13.10

ANSI Class 9001500 650 300 (80) 金属密封 17.20 16.50 15.50 14.40 350 11.50

450 17.20 17.20 14.20 13.10

ANSI Class 2500

650

300 (80) 金属密封

17.20 17.20 16.50

14.40

表4-2 气缸式双动作型执行机构

6300LA

Table 4-2 DOUBLE ACTING CYLINDER ACTUATOR(6300LA)

表4-2A 填料 聚四氟乙烯碳纤维 (P6528+P4519)介质温度

+230以下

Table 4-2A PACKING : TEFLON CARBON FIBER /MEDIUM TEMPERATURE : UNDER +230

平衡密封环强化聚四氟乙烯SUS316

Balance seal : Reinforced Teflon/SUS316

阀芯尺寸 Plug size ( inch )

公称压力

Body rating

执行机构

尺 寸

Actuator

size

气源压力

Air supply KPa G 阀座形式

Seat ring

1/2 5/8 1 1.25 1.5 2 2.5 3 4 5 7 8

金属密封 25.50 25.50 25.50 25.50 25.50 25.50 400

软密封 10.19 10.19 10.19 10.19 10.19 10.19 金属密封 25.50 25.50 25.50 25.50 25.50 25.50 200

500 软密封 10.19 10.19 10.19 10.19 10.19 10.19 金属密封 25.84 25.50 25.50 25.50 25.50 25.50 25.50 25.50 25.50 400

软密封 10.19 10.19 10.19 10.19 10.19 10.19 10.19 10.19 10.19 金属密封 25.84 25.50 25.50 25.50 25.50 25.50 25.50 25.50 25.50 300

500 软密封 10.19 10.19 10.19 10.19 10.19 10.19 10.19 10.19 10.19

金属密封 25.50 25.50 25.50 25.50 25.50 25.50 25.50 400

软密封 10.19 10.19 10.19 10.19 10.19 10.19 10.19 金属密封 25.50 25.50 25.50 25.50 25.50 25.50 25.50 450

500 软密封 10.19 10.19 10.19 10.19 10.19 10.19 10.19 金属密封 25.50 25.50 25.50 400

软密封 10.19 10.19 10.19 金属密封 25.50 25.50 25.50 ANSI Class 9001500

600

500 软密封 10.19 10.19 10.19 金属密封 40.90 40.00 38.90

36.10

400

软密封 10.19 10.19 10.19 10.19 金属密封 42.50 42.50 42.50 42.50 200

500 软密封 10.19 10.19 10.19 10.19 金属密封 42.50 42.50 42.50 42.50 42.50 42.50 42.50 42.50 400

软密封 10.19 10.19 10.19 10.19 10.19 10.19 10.19 10.19 金属密封 42.50 42.50 42.50 42.50 42.50 42.50 42.50 42.50 300

500 软密封 10.19 10.19 10.19 10.19 10.19 10.19

10.19 10.19 金属密封 42.50 42.50 42.50 400 软密封 10.19 10.19 10.19 金属密封 42.50 42.50 42.50 450

500 软密封 10.19 10.19 10.19 金属密封 42.50 400

软密封 10.19 金属密封 42.50 ANSI Class 2500

600

500 软密封

10.19

表4-2B 填料 柔性石墨(P6710CH+P6616CH)

介质温度

196

565 Table 4-2B PACKING : GRAFOIL/MEDIUM TEMPERATURE : 196

565

平衡密封环柔性石墨

Balance seal : GRAFOIL

阀芯尺寸 Plug size ( inch )

公称压力

Body rating

执行机构

尺 寸

Actuator

size 气源压力

Air supply KPa G 阀座形式

Seat ring

1/2 5/8 1 1.25 1.5 2 2.5 3 4 5 7 8

400 17.20 17.20 17.20 17.20 17.20 17.20 17.20 17.20 300

500 17.20 17.20 17.20 17.20 17.20 17.20 17.20 17.20

400 17.20 17.20 17.20 17.20 17.20 17.20 17.20

450 500 17.20 17.20 17.20 17.20 17.20 17.20 17.20 400 17.20 17.20 17.20 ANSI Class 9001500

600 500 金属密封

17.20 17.20 17.20 400 17.20 17.20 17.20 17.20 17.20 17.20 17.20

300 500 17.20 17.20 17.20 17.20 17.20 17.20

17.20 400 17.20 17.20 17.20 ANSI Class 2500

450

500

金属密封

17.20

17.20 17.20

图6 控制阀安装方位

5200LA

Fig. 6 ACTUATOR MOUNTING FORMS FOR 5200LA 图6-1 执行机构尺寸350450

Fig. 6-1 ACTUATOR SIZE : 350450

手轮 Side handle

定位器 Positioner

Flow direction

流体方向

手轮

Side handle

定位器 手轮

Positioner Side handle

Flow direction

流体方向

手轮 Side handle

Flow direction

流体方向

定位器

Positioner

手轮 Side handle

Flow direction

流体方向

定位器

Positioner

TYPE : S ( 标准 ) TYPE : R1

TYPE : R2 TYPE : R3

注安装位置为非标准时请指定安装位置的形式

TYPE

NOTE : Type S is automatically applied, unless otherwise specified.

图6-2. 执行机构尺寸

650

Fig. 6-2 ACTUATOR SIZE : 650

定位器 Positioner

Flow direction

流体方向

手轮 Side handle

定位器 Positioner

Flow direction

流体方向

手轮

Side handle

手轮 Side handle

Flow direction

流体方向

定位器

Positioner

手轮 Side handle

Flow direction

流体方向

手轮 Side handle

定位器

Positioner

TYPE : S ( 标准 )

TYPE : R1

TYPE : R2 TYPE : R3

表5 与标准执行机构组合时的产品重量

单位

kg

Table 5 NET WEIGHT OF STANDARD VALVE AND ACTUATOR COMBINED (UNIT: kg)

本表中所列重量均为执行机构和本体部的标准产品重量不包括附件手动机构等

Only standard types are represented. Weights of accessories, a handwheel and the like are not included.

表5-1 上阀盖形式

标准型

Table 5-1 BONNET TYPE : STANDARD TYPE

本体规格

Body rating

class

薄膜式执行机构

Diaphragm actuator size

5200LA

双动作气缸式执行机构

Double acting Cylinder

actuator size 6300LA

公称通径

Valves size

Inch (mm)

ANSI Class 350 450S 450L 650S 650L 200 300 450 600

9001500 87 115 105

1 (25) 2500 10

2 130 120 9001500 112 140 130 165 1.5 (40) 2500 137 165 155 190 9001500 147 175 165 200 2 (50) 2500 182 210 200 235 9001500 257 285 275 310

3 (80) 2500 322 350 340 375 9001500 328 350 455 380 485

4 (100) 2500 418 440 54

5 465 570 9001500 525 630 661 660 765

6 (150) 2500 635 740 771 770 870 9001500

725 830 861

850 950

8 (200) 2500 875 980 1011 945 1050 10 (250) 9001500 1263 1290 1390 12 (300)

9001500 1778 1805 1905

表5-2 上阀盖形式

散热片型

Table 5-2 BONNET TYPE : FIN-EXTENSION TYPE

本体规格

Body rating

class

薄膜式执行机构

Diaphragm actuator size

5200LA

双动作气缸式执行机构

Double acting Cylinder

actuator size 6300LA

公称通径

Valves size

Inch (mm)

ANSI Class 350 450S 450L 650S 650L 200 300 450 600

9001500 92 120

1 (25) 2500 107 135 9001500 117 145 170 1.5 (40)

2500 142 170 195 9001500 157 185 210 2 (50) 2500 192 220 245 9001500 267 295 320 3 (80) 2500 332 360 395 9001500 358 380 485 405 510 4 (100) 2500 473 465 570 495 600 9001500 560 665 695 690 795 6 (150) 2500 670 775 806 810 915

9001500

5 1000

8 (200) 2500 920 1025 1056 995 1100

10 (250) 9001500 1450 12 (300)

9001500 1985

DIMENSIONS UNIT : mm FACE TO FACE : L ANSI 900#,1500# ANSI 2500# ACTUATOR BONNET BONNET VALVE

SIZE SIZE WITH MANUAL HANDLE CODE STD. FIN EXT. STD.

FIN EXT. ANSI 900# RF ANSI 900# SW ANSI 900# BW ANSI 900# RTJ ANSI 1500# RF ANSI 1500# SW ANSI 1500# BW ANSI 1500# RTJ ANSI 2500# RF ANSI 2500# SW

ANSI 2500# BW

ANSI

2500# RTJ H1 H1 A B L1 CODE

No. 660 760 705 805 350 367 230 5235LA

1" (25A) 292 292 292 292 318 318

725 825 770 870 450 472 336 524SLA 695 845 745 5 350 367 230 5235LA

1.5" (40A) 333 333 333 333 447 450

760 910 810 960 450 472 336 524SLA 710 860 775 925 350 367 230 5235LA

2" (50A) 375 378 375 378 437 440

775 925 840 990 450 472 336 524SLA 780 930 835 985 350 367 230 5235LA

3" (80A) 440 443 460 463 498 505

845 995 900 1050 450 472 336 524SLA 4" (100A)

510 513 530 533 566 575 915 1065 975 1125 450 472

336

524SLA

*FLANGE IS FOLLOWING TO A STANDARD WHICH IS DESCRIBED ON SPECIFICATION SHEET.

DRAWING No.

5235LA N

NOTE

DIMENSIONS UNIT : mm FACE TO FACE : L ANSI 900#,1500# ANSI 2500# ACTUATOR BONNET BONNET VALVE

SIZE SIZE WITH MANUAL HANDLE CODE STD. FIN EXT. STD.

FIN EXT. ANSI 900# RF ANSI 900# SW ANSI 900# BW ANSI 900# RTJ ANSI 1500# RF ANSI 1500# SW ANSI 1500# BW ANSI 1500# RTJ ANSI 2500# RF ANSI 2500# SW

ANSI 2500# BW

ANSI

2500# RTJ H1 H1 A B L1 CODE

No. 700 800 745 845 350 367 230 5235LA

1" (25A) 292 292 292 292 318 318

765 865 810 910 450 472 336 524SLA 735 885 785 935 350 367 230 5235LA

1.5" (40A) 333 333 333 333 447 450

800 950 850 1000 450 472 336 524SLA 750 900 815 965 350 367 230 5235LA

2" (50A) 375 378 375 378 437 440

815 965 880 1030 450 472 336 524SLA 820 970 875 1025 350 367 230 5235LA

3" (80A) 440 443 460 463 498 505

885 1035 940 1090 450 472 336 524SLA 4" (100A)

510 513 530 533 566 575 955 1105 1015 1165 450 472

336

524SLA

*FLANGE IS FOLLOWING TO A STANDARD WHICH IS DESCRIBED ON SPECIFICATION SHEET.

DRAWING No.

5235LA N

NOTE

DIMENSIONS UNIT : mm FACE TO FACE : L ANSI 900#,1500# ANSI 2500# ACTUATOR BONNET BONNET VALVE

SIZE SIZE WITH MANUAL HANDLE CODE STD. FIN EXT. STD.

FIN EXT. ANSI 900# RF ANSI 900# SW ANSI 900# BW ANSI 900# RTJ ANSI 1500# RF ANSI 1500# SW ANSI 1500# BW ANSI 1500# RTJ ANSI 2500# RF ANSI 2500# SW

ANSI 2500# BW ANSI

2500# RTJ H1 H1 A B L1 CODE

No. 4" (100A) 510 513 530 533 566 575 915 1065 975 1125 450 472 336 524LLA 6" (150A) 715 718 770 776 820 833 1095 1245 1155 1305 450 472 336 524LLA 8" (200A)

854 857 911 920 1279 1295 1165 1315 1245 1395 450 472

336

524LLA

*FLANGE IS FOLLOWING TO A STANDARD WHICH IS DESCRIBED ON SPECIFICATION SHEET.

DRAWING No.

N

NOTE

DIMENSIONS UNIT : mm FACE TO FACE : L ANSI 900#,1500# ANSI 2500# ACTUATOR BONNET BONNET VALVE

SIZE SIZE WITH MANUAL HANDLE CODE STD. FIN EXT. STD.

FIN EXT. No. ANSI 900# RF ANSI 900# SW ANSI 900# BW ANSI 900# RTJ ANSI 1500# RF ANSI 1500# SW ANSI 1500# BW ANSI 1500# RTJ ANSI 2500# RF ANSI 2500# SW

ANSI 2500# BW ANSI

2500# RTJ H1 H1 A B L1 CODE

No. 4" (100A) 510 513 530 533 566 575 955 1105 1015 1165 450 472 336 524LLA 6" (150A) 715 718 770 776 820 833 1135 1285 1195 1345 450 472 336 524LLA 8" (200A)

854 857 911 920 1279 1295 1205 1355 1285 1435 450 472

336

524LLA

*FLANGE IS FOLLOWING TO A STANDARD WHICH IS DESCRIBED ON SPECIFICATION SHEET.

DRAWING No.

N

NOTE

DIMENSIONS UNIT : mm FACE TO FACE : L ANSI 900#,1500# ANSI 2500# ACTUATOR BONNET BONNET VALVE

SIZE SIZE WITH MANUAL HANDLE CODE STD. FIN EXT. STD.

FIN EXT. ANSI 900# RF ANSI 900# SW ANSI 900# BW ANSI 900# RTJ ANSI 1500# RF ANSI 1500# SW ANSI 1500# BW ANSI 1500# RTJ ANSI 2500# RF ANSI 2500# SW

ANSI 2500# BW ANSI

2500# RTJ H1 H1 A B H2 CODE

No. 4" (100A) 510 513 530 533 566 575 1000 1150 1060 1210 650 678 450 526SLA 6" (150A) 715 718 770 776 820 833 1180 1330 1240 1390 650 678 450 526SLA 8" (200A)

854 857 911 920 1279 1295 1250 1400 1330 1480 650 678 450 526SLA

*FLANGE IS FOLLOWING TO A STANDARD WHICH IS DESCRIBED ON SPECIFICATION SHEET.

DRAWING No.

NOTE

DIMENSIONS UNIT : mm FACE TO FACE : L ANSI 900#,1500# ANSI 2500# ACTUATOR BONNET BONNET VALVE

SIZE SIZE WITH MANUAL HANDLE CODE STD. FIN EXT. STD.

FIN EXT. ANSI 900# RF ANSI 900# SW ANSI 900# BW ANSI 900# RTJ ANSI 1500# RF ANSI 1500# SW ANSI 1500# BW ANSI 1500# RTJ ANSI 2500# RF ANSI 2500# SW

ANSI 2500# BW ANSI

2500# RTJ H1 H1 A B H2 CODE

No. 4" (100A) 510 513 530 533 566 575 1000 1150 1060 1210 650 678 450 526SLA 6" (150A) 715 718 770 776 820 833 1180 1330 1240 1390 650 678 450 526SLA 8" (200A)

854 857 911 920 1279 1295 1250 1400 1330 1480 650 678 450 526SLA

*FLANGE IS FOLLOWING TO A STANDARD WHICH IS DESCRIBED ON SPECIFICATION SHEET.

DRAWING No.

NOTE

DIMENSIONS UNIT : mm FACE TO FACE : L ANSI 900#,1500# ANSI 2500# ACTUATOR BONNET BONNET VALVE

SIZE SIZE WITH MANUAL HANDLE CODE STD. FIN EXT. STD.

FIN EXT. No. ANSI 900# RF ANSI 900# SW ANSI 900# BW ANSI 900# RTJ ANSI 1500# RF ANSI 1500# SW ANSI 1500# BW ANSI 1500# RTJ ANSI 2500# RF ANSI 2500# SW

ANSI 2500# BW ANSI

2500# RTJ H1 H1 A B H2 CODE

No. 6" (150A) 715 718 770 776 820 833 1280 1430 1340 1490 650 678 450 526LLA 8" (200A) 854 857 911 920 1279 1295 1350 1500 1430 1580 650 678 450 526LLA 10" (250A) 1251 1254 1327 1336

1440 1590

650 678 450 526LLA 12" (300A)

1311 1314 1400 1416

1540 1690

650

678 450 526LLA

*FLANGE IS FOLLOWING TO A STANDARD WHICH IS DESCRIBED ON SPECIFICATION SHEET. DRAWING No.

NOTE

DIMENSIONS UNIT : mm FACE TO FACE : L ANSI 900#,1500# ANSI 2500# ACTUATOR BONNET BONNET VALVE

SIZE SIZE WITH MANUAL HANDLE CODE STD. FIN EXT. STD.

FIN EXT. No. ANSI 900# RF ANSI 900# SW ANSI 900# BW ANSI 900# RTJ ANSI 1500# RF ANSI 1500# SW ANSI 1500# BW ANSI 1500# RTJ ANSI 2500# RF ANSI 2500# SW

ANSI 2500# BW ANSI

2500# RTJ H1 H1 A B H2 CODE

No. 6" (150A) 715 718 770 776 820 833 1280 1430 1340 1490 650 678 450 526LLA 8" (200A) 854 857 911 920 1279 1295 1350 1500 1430 1580 650 678 450 526LLA 10" (250A) 1251 1254 1327 1336

1440 1590

650 678 450 526LLA 12" (300A)

1311 1314 1400 1416

1540 1690

650

678 450 526LLA

*FLANGE IS FOLLOWING TO A STANDARD WHICH IS DESCRIBED ON SPECIFICATION SHEET. DRAWING No.

N NOTE

DIMENSIONS UNIT : mm FACE TO FACE : L

ANSI 900#,1500# ANSI 2500# ACTUATOR BONNET BONNET

VALVE

SIZE

WITH

MANUAL HANDLE CODE STD. FIN EXT. STD. FIN EXT. No. ANSI 900# RF ANSI 900# SW ANSI 900# BW ANSI 900# RTJ ANSI 1500# RF ANSI 1500# SW ANSI 1500# BW ANSI 1500# RTJ ANSI 2500# RF ANSI 2500# SW

ANSI

2500# BW

ANSI

2500# RTJ H1 H1 Cylin-der

SIZE

R H2 W CODE

No.

1" (25A) 292 292 292 292 318 318 990 1090 1035 1135 200 Rc3/8 465 320 6320LA 1.5" (40A) 333 333 333 333 447 450 1025 1175 1075 1225 200 Rc3/8 465 320 6320LA 2" (50A) 375 378 375 378 437 440 1040 1190 1105 1255 200 Rc3/8 465 320 6320LA 3" (80A)

440 443 460 463 498 505 1110 1260 1165 1315 200 Rc3/8 465 320 6320LA

*FLANGE IS FOLLOWING TO A STANDARD WHICH IS DESCRIBED ON SPECIFICATION SHEET. DRAWING No.

NOTE

DIMENSIONS UNIT : mm

FACE TO FACE : L ANSI 900#,1500# ANSI 2500# ACTUATOR BONNET BONNET VALVE

SIZE

WITH MANUAL HANDLE CODE STD. FIN EXT. STD. FIN EXT. No. ANSI 900# RF ANSI 900# SW ANSI 900# BW ANSI 900# RTJ ANSI 1500# RF ANSI 1500# SW ANSI 1500# BW ANSI 1500# RTJ ANSI 2500# RF ANSI 2500# SW

ANSI 2500# BW ANSI 2500# RTJ H1 H1 Cylin-der

SIZE R H2

L1 W CODE No. 93 1.5" (40A) 333 333 333 333 447 450 1085 1235 1135 1285 300 Rc1/2 615 260 400 6330LA 02 2" (50A) 375 378 375 378 437 440 1100 1250 1165 1315 300 Rc1/2 615 260 400 6330LA 03 3" (80A) 440 443 460 463 498 505 1170 1320 1225 1375 300 Rc1/2 615 260 400 6330LA 1240 1390 1300 1450 300 Rc1/2 615 260 400 6330LA

04 4" (100A) 510 513 530 533 566 575

1420 1570 1480 1630 450 Rc1/2 765 330 500 6345LA 1280 1430 1340 1490

300 Rc1/2 615 260 400 6330LA 06 6" (150A) 715 718 770 776 820 833

1460 1610 1520 1670 450 Rc1/2 765 330 500 6345LA 1510 1660 1590 1740

450 Rc1/2 765 330 500 6345LA 08 8" (200A) 854 857 911 920 1279 1295

10 1790 1720 1870 600 Rc3/4 870 445 630 6360LA 1570 1720

450 Rc1/2 765 330 500 6345LA 10 10" (250A) 1251 1254 1327 1336 1700 1850 600 Rc3/4 870 445 630 6360LA 1670 1820

450 Rc1/2 765 330 500 6345LA 12

12" (300A)

1311 1314 1400 1416

1800 1950

600 Rc3/4 870 445 630 6360LA

*FLANGE IS FOLLOWING TO A STANDARD WHICH IS DESCRIBED ON SPECIFICATION SHEET.

DRAWING No.

N

NOTE