H3C无线APfat设置

> WA2200上配置两个vlan：vlan 1000和vlan 256

> vlan 1000为管理vlan；vlan 256为业务vlan，所有的无线客户端都属于vlan 256

> WA2200的管理IP地址为10.10.1.50/24

> 服务集标识SSID为H3C-wireless，无认证无加密

重要！无线接入点设备FAT模式的启动版本文件名固定为wa2200_fat.bin/wa1208_fat.bin，不能以其他名称作为版本文件名！

> 步骤一：创建业务vlan（vlan256）和管理vlan（vlan 1000），并配置管理IP地址

    [H3C] vlan 256 

    [H3C-vlan256] quit                

    [H3C] vlan 1000  

    [H3C-vlan1000] quit            

    [H3C] interface vlan 1000                            

    [H3C-Vlan-interface1000] ip address 10.10.1.50 255.255.255.0       

    [H3C-Vlan-interface1000] quit 

> 步骤二：将上行以太网口配置为Trunk类型

    [H3C] interface Ethernet 1/0/1

    [H3C-Ethernet1/0/1] port link-type trunk     

    [H3C-Ethernet1/0/1] port trunk permit vlan all

> 步骤三：创建无线接口       

    [H3C] interface WLAN-BSS 1     //为射频服务

    [H3C-WLAN-BSS1] port access vlan 256 

> 步骤四：创建无线服务模板（SSID名称为H3C-wireless）

    [H3C] wlan service-template 1 clear   //为射频服务

    [H3C-wlan-st-1] authentication-method open-system                

    [H3C-wlan-st-1] ssid H3C-wireless

　　[H3C-wlan-st-1] service-template enable

　　加密方法

wlan service-template 1 crypto 

ssid H3C-wep 

authentication-method open-system 

cipher-suite wep40 

wep default-key 1 wep40 pass-phrase 12345 

service-template enable

> 步骤五：在11g射频卡上绑定无线服务模板和无线接口，配置信道为11、功率为15dBm

    [H3C] interface WLAN-Radio 1/0/1  //定义射频

    [H3C-WLAN-Radio1/0/1] service-template 1 interface WLAN-BSS 1   

    [H3C-WLAN-Radio1/0/1] channel 11

    [H3C-WLAN-Radio1/0/1] max-power 15

    注：默认情况下，功率为20dBm（即100mW）；信道为自动调整。

#                                                                               

 version 5.20, 0001                                                             

#                                                                               

 sysname H3C                                                                    

#                                                                               

 password-control login-attempt 3 exceed lock-time 120                          

#                                                                               

 domain default enable system                                                   

#                                                                               

vlan 1                                                                          

#                                                                               

vlan 256                                                                        

#                                                                               

vlan 1000                                                                       

#                                                                               

domain system                                                                   

 access-limit disable                                                           

 state active                                                                   

 idle-cut disable                                                               

 self-service-url disable                                                       

#                                                                               

wlan rrm                                                                        

 11a mandatory-rate 6 12 24                                                     

 11a supported-rate 9 18 36 48 54                                               

 11b mandatory-rate 1 2                                                         

 11b supported-rate 5.5 11                                                      

 11g mandatory-rate 1 2 5.5 11                                                  

 11g supported-rate 6 9 12 18 24 36 48 54                                       

#                                                                               

wlan service-template 1 clear                                                   

 ssid H3C-wireless                                                              

 authentication-method open-system                                              

 service-template enable                                                        

#                                                                               

interface NULL0                                                                 

#                                                                               

interface Vlan-interface1000                                                    

 ip address 10.10.1.50 255.255.255.0                                            

#                                                                               

interface Ethernet1/0/1                                                         

 port link-type trunk                                                           

 port trunk permit vlan all                                                     

#                                                                               

interface Ethernet1/0/2                                                         

#                                                                               

interface WLAN-BSS1                                                             

 port access vlan 256                                                           

#                                                                               

interface WLAN-Radio1/0/1                                                       

 channel 11                                                                      

 service-template 1 interface wlan-bss 1                                        

#                                                                               

interface WLAN-Radio1/0/2                                                       

#                                                                               

user-interface con 0                                                            

user-interface vty 0 4                                                          

#                                                                               

return