LP141XA

The LP141XA is a Color Active Matrix Liquid Crystal Display with an integral Cold Cathode Fluorescent Lamp(CCFL) back light system. The matrix employs a-Si Thin Film Transistor as the active element. It is a transmissive type display operating in the normally white mode. This TFT-LCD has a 13.3 inch diagonally measured active display area with XGA resolution(768 vertical by 1024 horizontal pixel array). Each pixel is divided into Red, Green and Blue sub-pixels or dots which are arranged in vertical stripes. Gray scale or the brightness of the sub-pixel color is determined with a 6-bit gray scale signal for each dot, thus, presenting a palette of more than 262,144 colors.

The LP141XA has been designed to apply the interface method that enables low power, high speed low EMI. Flat Link must be used as a LVDS(Low Voltage Differential Signaling) chip.

The LP141XA is intended to support applications where thin thickness, low power are critical factors and graphic displays are important. In combination with the vertical arrangement of the sub-pixels, the LP141XA characteristics provide an excellent flat panel display for office automation products such as Notebook PC.

General Features

Active screen size 14.1 inches(33.78cm) diagonal

Outline dimensions 298.5(H) ¡¿ 227.5(V) ¡¿ 5.8(D) mm (typ)

Pixel pitch 0.279 mm ¡¿ 0.279 mm

Pixel format 1024 horiz. By 768 vert. pixels

RGB stripe arrangement

Color depth 6-bit, 262,144 colors

Luminance, White 120 cd/m2 (typ)

Power Consumption Total 4.97Watt(typ)

Weight 590g (max)

Display operating mode transmissive mode, normally white

Surface treatments hard coating(3H), anti-glare treatment of the front polarizer

2. Electrical Specifications 2-1. Electrical Characteristics

The LP141XA requires two power inputs. One is employed to power the LCD electronics and to drive the TFT array and liquid crystal. The second input which powers the CCFL, is typically generated by an inverter. The inverter is an external unit to the LCD.

Table 1 ELECTRICAL CHARACTERISTICS:

Values

Min. Typ. Max. MODULE: Power Supply Input Voltage Power Supply Input Current Differential Impedance Power Consumption Rush current LAMP Operating Voltage Operating Current Established Starting Voltage at 25¡É at 0¡É Operating Frequency Power Consumption Life Time V CC I CC Zm P c I RUSH V BL I BL f BL P BL 3.0 - 90 - - 680 3.0 - - 40 - 10,000 3.3 0.410 100 1.35 1.5 725 5.0 - - 60 3.63 3.6 0.620 110 2.05 1.8 850 6.0 1170 1450 80 4.08 - Vdc A ohm Watts A V RMS mA V RMS V RMS kHz Watts Hrs 1 2 1 3 4 5 6 7

Notes: 1. The specified current and power consumption are under the Vcc = 3.3V , 25¡É, fv = 60Hz condition

whereas Black pattern is displayed.

2. This impedance value is needed to proper display and measured form LVDS Tx to the mating connector.

3. The duration of rush current is about 20ms.

4. The variance of the voltage is ¡¾10%.

5. The transformer output voltage in the inverter must be high considering to the loss of the ballast capacitor in the inverter.

6. The lamp power consumption shown above does not include loss of external inverter.

7. The life time is determined as the time at which brightness of lamp is 50% compare to that of initial

value at the typical lamp current on condition of continuous operating at 25¡É¡¾2¡É

Notes Units Symbol

Parameter

2-2. Interface Connections

This LCD employs two interface connections, a 20 pin connector is used for the module electronics and the other connector is used for the integral backlight system.

The electronics interface connector is a model FI-SEB-20P-HF manufactured by JAE or equivalent. The pin configuration for the connector is shown in the table below.

The backlight interface connector is a model BHSR-02VS-1, manufactured by JST. The mating connector part number is SM02B-BHSS-1 or equivalent. The pin configuration for the connector is shown in the table below.

Table 3 BACKLIGHT CONNECTOR PIN CONFIGURATION [CN2]

Pin Symbol Description Notes

1 2 HV

LV

Power supply for lamp

(High voltage side)

Power supply for lamp

(Low voltage side)

1

2

Notes: 1. The high voltage side terminal is colored pink.

2. The low voltage side terminal is colored black.

Notes 1. Unspecified dimensional tolerance are ¡¾0.5mm

< REAR VIEW >

3.PRECAUTIONS

The LCD Products listed on this documents are not suitable for use of Military,Industry,Medical etc.

system.

If customers intend to use these LCD products for above application, Please contact ours sales people in advance.