汽车起重机吨位选择依靠特性曲线表，根据站车位置确定站车幅度，再根据起吊高度等确定出杆长度，进而根据特性曲线表选择合理的起重机规格，节约吊装成本。
8吨汽车起重机性能表 2
20吨汽车吊机额定性能表 3
25吨汽车起重机起重性能表（主臂） 4
30吨汽车起重机性能表（一） 6
50吨汽车起重机性能表（主表） 8
80吨汽车起重机起重性能表(一) 10
100t汽车吊性能表 12
120吨汽车起重机起重性能表 13
150吨汽车起重机性能表(一) 14
150吨汽车起重机性能表(二) 15
160t汽车吊性能表 16
200吨汽车吊车 17
260吨吊车性能表 18
LTM1300/1-300t全液压汽车吊机 19
LTM1500-500t全液压汽车吊机 22
LTM1500-500t全液压汽车吊机 23
8吨汽车起重机性能表
| 主要技术参数 | 6.95m吊臂 | 8.50m吊臂 | 10.15m吊臂 | 11.70m吊臂 | |||||||||
| 参数名称 | 参数 | 工作 半径 (m) | 起升 高度 (m) | 起重量 (t) | 工作 半径 (m) | 起升 高度 (m) | 起重量 (t) | 工作 半径 (m) | 起升 高度 (m) | 起重量 (t) | 工作 半径 (m) | 起升高度 (m) | 起重量 (t) |
| 全车总重 | 15.50t | 3.2 | 7.5 | 8.0 | 3.4 | 9.2 | 6.7 | 4.2 | 10.6 | 4.2 | 4.9 | 12.0 | 3.2 |
| 最大爬坡能力 | 22% | 3.7 | 7.1 | 5.4 | 4.0 | 8.8 | 4.5 | 5.0 | 10.1 | 3.1 | 5.8 | 11.4 | 2.4 |
| 吊臂最大仰角 | 4.3 | 6.5 | 4.0 | 4.7 | 8.3 | 3.4 | 5.7 | 9.6 | 2.5 | 6.7 | 10.8 | 1.9 | |
| 吊臂全伸时长度 | 11.70m | 4.9 | 5.7 | 3.2 | 5.4 | 7.6 | 2.7 | 6.6 | 8.8 | 1.9 | 7.7 | 9.9 | 1.4 |
| 吊臂全缩时长度 | 6.95m | 5.5 | 4.6 | 2.6 | 6.2 | 6.8 | 2.2 | 7.5 | 7.7 | 1.5 | 8.8 | 8.6 | 1.0 |
| 最大提升高度 | 12.00m | 6.9 | 5.6 | 1.8 | 8.4 | 6.3 | 1.2 | 9.7 | 7.0 | 0.9 | |||
| 最小工作半径 | 3.20m | 7.5 | 4.2 | 1.5 | 9.0 | 4.8 | 1.0 | 10.5 | 5.2 | 0.8 | |||
| 最小转弯半径 | 9.20m | ||||||||||||
以下工况仅供参考，实际请与本公司业务员联系！
| 回转半径（m） | 主臂长度（m） | 主臂+付臂 | ||||||
| 10.2 | 12.58 | 14.97 | 17.35 | 19.73 | 22.12 | 24.5 | 24.5+7.5 | |
| 3.0 | 20 | —— | —— | —— | —— | —— | —— | —— |
| 3.5 | 17.2 | 15.9 | —— | —— | —— | —— | —— | —— |
| 4.0 | 14.6 | 14.6 | 12.6 | —— | —— | —— | —— | —— |
| 4.5 | 12.75 | 12.7 | 11.7 | 10.5 | —— | —— | —— | —— |
| 5.0 | 11.6 | 11.3 | 11.3 | 9.7 | —— | —— | —— | —— |
| 5.5 | 10.45 | 10 | 10 | 9.1 | 8.1 | —— | —— | —— |
| 6.0 | 9.3 | 9 | 9 | 8.5 | 7.6 | 6.9 | —— | —— |
| 7.0 | 7.24 | 7.3 | 7.41 | 7.2 | 6.7 | 6.1 | 5.5 | —— |
| 8.0 | 5.99 | 6.1 | 6.17 | 6.22 | 5.9 | 5.4 | 5 | —— |
| 9.0 | —— | 5.13 | 5.21 | 5.25 | 5.3 | 4.8 | 4.5 | —— |
| 10.0 | —— | 4.35 | 4.43 | 4.48 | 4.52 | 4.4 | 4 | 2.1 |
| 12.0 | —— | —— | 3.26 | 3.32 | 3.36 | 3.39 | 3.41 | 1.7 |
| 14.0 | —— | —— | —— | 2.49 | 2.53 | 2.56 | 2.58 | 1.4 |
| 16.0 | —— | —— | —— | —— | 1.9 | 1.94 | 1.96 | 1.2 |
| 18.0 | —— | —— | —— | —— | —— | 1.45 | 1.47 | 1 |
| 20.0 | —— | —— | —— | —— | —— | —— | 1.08 | 0.88 |
| 22.0 | —— | —— | —— | —— | —— | —— | 0.76 | 0.75 |
| 24.0 | —— | —— | —— | —— | —— | —— | —— | 0.63 |
| 27.0 | —— | —— | —— | —— | —— | —— | —— | 0.5 |
以下工况仅供参考，实际请与本公司业务员联系！
| 工作半径(m) | 吊臂长度(m) | ||||||
| 10.2 | 13.75 | 17.3 | 20.85 | 24.4 | 27.95 | 31.5 | |
| 3 | 25 | 17.5 | |||||
| 3.5 | 20.6 | 17.5 | 12.2 | 9.5 | |||
| 4 | 18 | 17.5 | 12.2 | 9.5 | |||
| 4.5 | 16.3 | 15.3 | 12.2 | 9.5 | 7.5 | ||
| 5 | 14.5 | 14.4 | 12.2 | 9.5 | 7.5 | ||
| 5.5 | 13.5 | 13.2 | 12.2 | 9.5 | 7.5 | 7 | |
| 6 | 12.3 | 12.2 | 11.3 | 9.2 | 7.5 | 7 | 5.1 |
| 6.5 | 11.2 | 11 | 10.5 | 8.8 | 7.5 | 7 | 5.1 |
| 7 | 10.2 | 10 | 9.8 | 8.5 | 7.2 | 7 | 5.1 |
| 7.5 | 9.4 | 9.2 | 9.1 | 8.1 | 6.8 | 6.7 | 5.1 |
| 8 | 8.6 | 8.4 | 8.4 | 7.8 | 6.6 | 6.4 | 5.1 |
| 8.5 | 8 | 7.9 | 7.8 | 7.4 | 6.3 | 7.2 | 5 |
| 9 | 7.2 | 7 | 6.8 | 6 | 6.1 | 4.8 | |
| 10 | 6 | 5.8 | 5.6 | 5.6 | 5.3 | 4.4 | |
| 12 | 4 | 4.1 | 4.1 | 4.2 | 3.9 | 3.7 | |
| 14 | 2.9 | 3 | 3.1 | 2.9 | 3 | ||
| 16 | 2.2 | 2.3 | 2.2 | 2.3 | |||
| 18 | 1.6 | 1.8 | 1.7 | 1.7 | |||
| 20 | 1.3 | 1.3 | 1.3 | ||||
| 22 | 1 | 0.9 | 1 | ||||
| 24 | 0.7 | 0.8 | |||||
| 26 | 0.5 | 0.5 | |||||
| 28 | 0.4 | ||||||
| 29 | 0.3 | ||||||
| 30 |
25吨汽车起重机起重性能表（副臂）
| 主臂主角 | 7.5副臂 | |
| 副臂倾角5度 | 副臂倾角30度 | |
| 80度 | 2.5 | 1.25 |
| 75度 | 2.5 | 1.25 |
| 70度 | 2.05 | 1.15 |
| 65度 | 1.75 | 1.1 |
| 60度 | 1.55 | 1.05 |
| 55度 | 1.3 | 1.0 |
| 50度 | 1.05 | 0.8 |
| 主要技术参数 | 主臂起重性能 | ||||||
| 工作半径（m） | 支腿全伸 | 不用支腿 | |||||
| 名称 | 参数 | 10.00m | 17.00m | 24.00m | 31.00m | 10.00m | |
| 全车总重 | 32.2t | 3.00 | 30.00 | 20.00 | 8.00 | ||
| 最大爬坡能力 | 31% | 3.35 | 30.00 | 20.00 | 7.00 | ||
| 最大提升高度 | 34.00m | 3.50 | 28.10 | 20.00 | 6.40 | ||
| 吊臂全伸时长度 | 31.00m | 4.00 | 24.20 | 20.00 | 5.10 | ||
| 吊臂全缩时长度 | 10.00m | 4.50 | 21.40 | 20.00 | 13.00 | 4.20 | |
| 最小转弯半径 | 11.50m | 4.8 | 20.00 | 20.00 | 13.00 | 3.70 | |
| 最大仰角 | 80° | 5.0 | 19.20 | 19.20 | 13.00 | 3.40 | |
| 30t吊钩重 | 0.35t | 5.5 | 17.50 | 17.50 | 13.00 | 2.80 | |
| 12t吊钩重 | 0.20t | 6.0 | 16.00 | 16.00 | 13.00 | 2.30 | |
| 4t吊钩重 | 0.10t | 6.5 | 14.60 | 14.60 | 13.00 | 9.00 | 1.90 |
| 10m吊臂时钢丝绳数 | 8根 | 7.0 | 13.50 | 13.50 | 12.00 | 9.00 | 1.60 |
| 10-17m时钢丝绳数 | 5根 | 7.5 | 12.00 | 12.00 | 11.20 | 9.00 | 1.30 |
| 24m时钢丝绳数 | 4根 | 8.0 | 10.50 | 10.50 | 10.50 | 9.00 | 1.00 |
| 31m时钢丝绳数 | 3根 | 8.5 | 9.40 | 9.40 | 9.00 | ||
| 9.8 | 7.20 | 7.20 | 7.70 | ||||
| 10.0 | 6.95 | 6.95 | 7.50 | ||||
| 11.0 | 5.80 | 5.80 | 6.40 | ||||
| 12.0 | 4.90 | 4.90 | 5.55 | ||||
| 14.0 | 3.45 | 3.45 | 4.20 | ||||
| 16.0 | 2.50 | 3.20 | |||||
| 18.0 | 1.80 | 2.45 | |||||
| 20.0 | 1.30 | 1.90 | |||||
| 22.0 | 0.85 | 1.50 | |||||
| 24.0 | 1.10 | ||||||
| 26.0 | 0.75 | ||||||
| 27.0 | 0.65 |
30吨汽车起重机性能表（二）
| 吊臂角度 | 工作半径 | 使用8.45m 副臂倾角5° | 吊臂角度 | 工作半径 | 使用13.5m副臂倾角5° |
| 80° | 7.9 | 4.00 | 80° | 9.3 | 2.50 |
| 78.5° | 9.5 | 4.00 | 77° | 12.0 | 2.50 |
| 78° | 10.2 | 3.80 | 76° | 12.7 | 2.35 |
| 76° | 11.2 | 3.30 | 74° | 14.1 | 2.10 |
| 74° | 12.2 | 2.90 | 72° | 15.6 | 1.95 |
| 72° | 13.4 | 2.70 | 70° | 17.1 | 1.80 |
| 70° | 14.6 | 2.50 | 68° | 18.5 | 1.65 |
| 68° | 16.0 | 2.35 | 66° | 19.9 | 1.50 |
| 66° | 17.3 | 2.20 | ° | 21.3 | 1.40 |
| ° | 18.5 | 2.10 | 62° | 22.7 | 1.30 |
| 62° | 19.8 | 2.05 | 60° | 24.0 | 1.20 |
| 60° | 20.7 | 1.85 | 58° | 25.3 | 1.15 |
| 58° | 21.9 | 1.65 | 55° | 27.1 | 1.05 |
| 55° | 23.6 | 1.30 | 54° | 27.7 | 0.95 |
| 54° | 24.1 | 1.15 | 52° | 28.8 | 0.80 |
| 52° | 25.0 | 0.95 | 50° | 29.9 | 0.65 |
| 50° | 25.8 | 0.75 | 48° | 30.9 | 0.55 |
| 48° | 26.8 | 0.60 |
2、使用副臂吊装时，主臂的角度不得大于45，否则将倾翻
50吨汽车起重机性能表（主表）
以下工况仅供参考，实际请与本公司业务员联系！
| 不支第五支腿，吊臂位于起重机前方或后方；支起第五支腿，吊臂位于侧方、后方、前方 | ||||||
| 工作半径(m) | 主臂长度(m) | |||||
| 10.70 | 18.00 | 25.40 | 32.75 | 40.10 | ||
| 3.0 | 50.00 | |||||
| 3.5 | 43.00 | |||||
| 4.0 | 38.00 | |||||
| 4.5 | 34.00 | |||||
| 5.0 | 30.00 | 24.70 | ||||
| 5.5 | 28.00 | 23.50 | ||||
| 6.0 | 24.00 | 22.20 | 16.30 | |||
| 6.5 | 21.00 | 20.00 | 15.00 | |||
| 7.0 | 18.50 | 18.00 | 14.10 | 10.20 | ||
| 8.0 | 14.50 | 14.00 | 12.40 | 9.20 | 7.50 | |
| 9.0 | 11.50 | 11.20 | 11.10 | 8.30 | 6.50 | |
| 10.0 | 9.20 | 10.00 | 7.50 | 6.00 | ||
| 12.0 | 6.40 | 7.50 | 6.80 | 5.20 | ||
| 14.0 | 5.10 | 5.70 | 4.60 | |||
| 16.0 | 4.00 | 4.70 | 3.90 | |||
| 18.0 | 3.10 | 3.70 | 3.30 | |||
| 20.0 | 2.20 | 2.90 | 2.90 | |||
| 22.0 | 1.60 | 2.30 | 2.40 | |||
| 24.0 | 1.80 | 2.00 | ||||
| 26.0 | 1.40 | 1.50 | ||||
| 28.0 | 1.20 | |||||
| 30.0 | 0.90 | |||||
| 各臂伸缩率 （%） | 二 | 0 | 100 | 100 | 100 | 100 |
| 三 | 0 | 0 | 33 | 66 | 100 | |
| 四 | 0 | 0 | 33 | 66 | 100 | |
| 五 | 0 | 0 | 33 | 66 | 100 | |
| 钢丝绳倍率 | 12 | 8 | 5 | 4 | 3 | |
| 吊钩重量 | 0.515 | 0.215 | ||||
50吨汽车起重机性能表（副臂）
| 吊臂位于起重机侧方或后方 | |||||||
| 主臂仰角（°） | 吊臂长度（m） | ||||||
| 40.10+5.10 主臂+副臂 | 40.10+9.00 主臂+副臂 | 40.10+16.10 主臂+副臂 | |||||
| 0° | 20° | 0° | 20° | 0° | 20° | ||
| 78 | 4.0 | 3.6 | 3.2 | 1.9 | 1.5 | 0.8 | |
| 75 | 3.8 | 3.2 | 3.0 | 1.8 | 1.3 | 0.8 | |
| 72 | 3.2 | 2.9 | 2.8 | 1.7 | 1.2 | 0.7 | |
| 70 | 3.0 | 2.5 | 2.5 | 1.6 | 1.2 | 0.6 | |
| 65 | 2.5 | 2.0 | 2.0 | 1.4 | 1.1 | 0.5 | |
| 60 | 1.9 | 1.6 | 1.5 | 1.0 | 0.8 | 0.5 | |
| 55 | 1.4 | 0.8 | 1.0 | 0.6 | 0.6 | 0.4 | |
| 各节臂伸缩率(%) | 二 | 100 | |||||
| 三 | |||||||
| 四 | |||||||
| 五 | |||||||
| 钢丝绳倍率 | 1 | ||||||
| 吊钩重量 | 0.1 | ||||||
以下工况仅供参考，实际请与本公司业务员联系！
| 主臂起重性能表 | ||||||||
| 工作半径(m) | 吊臂长度(支腿全伸) | 吊臂长度 (不伸支腿) | ||||||
| 12.0m | 18.0m | 24.0m | 30.0m | 36.0m | 40.0m | 44.0m | 12.0m | |
| 2.5 | 80.0 | 45.0 | 15.0 | |||||
| 3.0 | 80.0 | 45.0 | 35.0 | 15.0 | ||||
| 3.5 | 80.0 | 45.0 | 35.0 | 15.0 | ||||
| 4.0 | 70.0 | 45.0 | 35.0 | 11.7 | ||||
| 4.5 | 62.0 | 45.0 | 35.0 | 27.0 | 9.5 | |||
| 5.0 | 56.0 | 40.0 | 32.0 | 27.0 | 8.0 | |||
| 5.5 | 50.0 | 37.0 | 29.2 | 27.0 | 22.0 | 6.8 | ||
| 6.0 | 45.0 | 34.3 | 27.2 | 25.0 | 22.0 | 5.8 | ||
| 6.5 | 39.4 | 31.5 | 25.3 | 23.2 | 22.0 | 18.0 | 5.0 | |
| 7.0 | 35.6 | 29.1 | 23.7 | 21.5 | 20.3 | 18.0 | 4.3 | |
| 8.0 | 27.8 | 25.4 | 21.0 | 18.8 | 17.7 | 15.7 | 12.0 | 3.2 |
| 9.5 | 20.8 | 20.8 | 17.8 | 15.7 | 14.6 | 13.2 | 12.0 | 2.0 |
| 10.0 | 19.2 | 19.2 | 17.0 | 15.0 | 13.8 | 12.6 | 11.4 | 1.7 |
| 11.0 | 16.5 | 15.6 | 13.5 | 12.4 | 11.4 | 10.4 | ||
| 11.8 | 14.7 | 14.7 | 12.6 | 11.4 | 10.6 | 9.7 | ||
| 12.0 | 14.2 | 14.2 | 12.4 | 11.2 | 10.4 | 9.5 | ||
| 13.0 | 12.5 | 12.5 | 11.3 | 10.2 | 9.3 | 8.8 | ||
| 14.6 | 10.0 | 10.0 | 10.0 | 9.0 | 8.5 | 7.8 | ||
| 15.0 | 9.4 | 9.4 | 9.4 | 8.7 | 8.2 | 7.6 | ||
| 16.0 | 8.1 | 8.1 | 8.1 | 7.7 | 7.1 | |||
| 17.8 | 6.2 | 6.2 | 6.2 | 6.8 | 6.3 | |||
| 20.0 | 4.5 | 4.5 | 4.5 | 5.1 | 5.6 | |||
| 22.0 | 3.4 | 3.4 | 4.0 | 4.4 | ||||
| 23.0 | 3.0 | 3.0 | 3.5 | 3.9 | ||||
| 26.0 | 1.7 | 2.2 | 2.6 | |||||
| 27.0 | 1.9 | 2.2 | ||||||
| 28.0 | 1.6 | 1.9 | ||||||
| 30.0 | 1.0 | 1.3 | ||||||
| 31.0 | 1.1 |
| 主要技术参数 | 副臂起重性能 | |||||
| 主臂仰角 | 支腿全伸在两侧或后部吊装 | |||||
| 名称 | 参数 | 44m主臂+9.5m副臂5°夹角 | 44m主臂+15m副臂5°夹角 | |||
| 工作半径(m) | 起重性能(t) | 工作半径(m) | 起重性能(t) | |||
| 全车总重 | 63.00t | 81.3° | 10.0 | 6.00 | 11.5 | 4.00 |
| 主臂全伸时长度 | 44.00m | 80.4° | 11.0 | 6.00 | 12.6 | 4.00 |
| 主臂全缩时长度 | 12.00m | 80.1° | 11.3 | 5.90 | 13.0 | 4.00 |
| 最大仰角 | 82° | 78.6° | 13.0 | 5.20 | 14.6 | 3.75 |
| 最大爬坡能力 | 16% | 75.2° | 16.0 | 4.40 | 18.2 | 3.05 |
| 最小转弯半径 | 15.40% | 70.8° | 20.0 | 3.60 | 22.5 | 2.55 |
| 最大提升高度 | 58.50m | 66.0° | 24.0 | 3.00 | 27.2 | 2.10 |
| 80t主吊钩重 | 1t | 63.8° | 26.0 | 2.75 | 29.1 | 2.05 |
| 80t辅助吊钩重 | 0.5t | 58.0° | 30.3 | 1.50 | 34.0 | 1.20 |
| 6t副吊钩重 | 0.25t | 55.4° | 32.0 | 1.20 | ||
120吨汽车起重机起重性能表
以下工况仅供参考，实际请与本公司业务员联系！
| 工作半径(m) | 主 臂 长 度(m) | ||||||||||||
| 12.6 | 12.6 | 16.6 | 20.6 | 24.5 | 28.5 | 32.5 | 36.5 | 40.5 | 44.5 | 48.5 | 52.5 | 56.0 | |
| 3 | 120 | 111 | |||||||||||
| 3.5 | 107 | 102 | 92 | ||||||||||
| 4 | 95 | 94 | 88 | 81 | 69 | ||||||||
| 4.5 | 86 | 82 | 75 | 66 | |||||||||
| 5 | 79 | 76 | 70 | 62 | 51 | ||||||||
| 6 | 66 | 66 | 62 | 55 | 49 | 40 | |||||||
| 7 | 56 | 56 | 55 | 49 | 44.5 | 38 | 32 | 23.6 | |||||
| 8 | 48.5 | 48 | 47 | 44 | 40 | 38.5 | 32 | 22.1 | 20.1 | ||||
| 9 | 42 | 41.5 | 40.5 | 40 | 36.5 | 32.5 | 29.8 | 21.3 | 19.9 | 15.8 | |||
| 10 | 37 | 36.5 | 35.5 | 35.5 | 33.5 | 30.5 | 27.9 | 21.3 | 19.7 | 15.8 | 14.9 | 12.6 | |
| 12 | 29.1 | 28 | 28.9 | 27.8 | 26.2 | 24.5 | 21.3 | 18.7 | 15.8 | 14.5 | 11.8 | ||
| 14 | 24.8 | 22.7 | 23.5 | 22.5 | 22.5 | 21.6 | 18.9 | 16.8 | 15 | 13.3 | 11.1 | ||
| 16 | 18.3 | 19.4 | 18.4 | 19 | 19.1 | 16.9 | 15.1 | 13.6 | 12.2 | 10.3 | |||
| 18 | 15.8 | 15.8 | 15.2 | 16.8 | 16.3 | 15 | 13.5 | 12.3 | 11.1 | 9.6 | |||
| 20 | 13.2 | 13.8 | 14.1 | 14.2 | 13.4 | 12.2 | 11.1 | 10.2 | 8.9 | ||||
| 22 | 11.5 | 12.4 | 12.2 | 12.1 | 11.7 | 10.9 | 10.1 | 9.4 | 8.3 | ||||
| 24 | 10.7 | 10.5 | 10.4 | 10 | 9.9 | 9.2 | 8.6 | 7.7 | |||||
| 26 | 9.3 | 9.2 | 9 | 8.5 | 8.6 | 8.3 | 8 | 7.2 | |||||
| 28 | 8 | 8 | 7.3 | 7.4 | 7.6 | 7.4 | 6.7 | ||||||
| 30 | 7 | 7.2 | 6.5 | 6.3 | 6.5 | 6.9 | 6.3 | ||||||
| 32 | 6.3 | 6 | 5.6 | 6 | 6.1 | 5.8 | |||||||
| 34 | 5.5 | 5.6 | 5.2 | 5.6 | 5.3 | 5.2 | |||||||
| 36 | 5.1 | 4.8 | 5.1 | 4.5 | 4.5 | ||||||||
| 38 | 4.7 | 4.5 | 4.4 | 4 | 3.9 | ||||||||
| 40 | 4.2 | 4 | 3.5 | 3.7 | |||||||||
| 42 | 3.9 | 3.6 | 3.2 | 3.5 | |||||||||
| 44 | 3.2 | 2.8 | 2.7 | ||||||||||
| 46 | 2.6 | 2.4 | 2.7 | ||||||||||
| 48 | 2 | 2 | |||||||||||
| 50 | 1.7 | 1.7 | |||||||||||
| 52 | 1.4 | ||||||||||||
| 54 | 1.2 |
以下工况仅供参考，实际请与本公司业务员联系！
| 主臂360° 75%起重性能 | ||||||||||
| 工作半径(m) | 吊臂长度(m) | |||||||||
| 13.9 | 17.7 | 21.3 | 25.0 | 28.7 | 32.3 | 36.0 | 39.6 | 43.1 | 52.8 | |
| 3.0 | 140 | |||||||||
| 3.6 | 126.9 | 65.2 | .4 | |||||||
| 4.0 | 122.9 | 65.1 | 63.7 | |||||||
| 4.5 | 108.9 | 65.1 | 63.9 | 56.5 | ||||||
| 5.0 | 99.8 | 65.1 | 61.4 | 55.4 | ||||||
| 6.0 | 80.3 | 65.0 | 56.6 | 51.7 | 46.6 | 40.8 | ||||
| 7.0 | 68.9 | 62.0 | 53.3 | 47.2 | 43.9 | 37.8 | 33.1 | 31.5 | ||
| 8.0 | 58.7 | 57.1 | 48.1 | 44.6 | 30.0 | 34.4 | 31.9 | 30.2 | ||
| 9.0 | 49.4 | 49.2 | 44.9 | 41.2 | 35.8 | 31.9 | 29.8 | 27.2 | 27.0 | |
| 10.0 | 42.0 | 41.9 | 41.6 | 35.7 | 33.8 | 29.5 | 27.2 | 25.4 | 24.8 | |
| 12.0 | 29.8 | 29.8 | 29.2 | 27.7 | 24.6 | 23.3 | 21.8 | 21.3 | 17.6 | |
| 14.0 | 21.6 | 21.6 | 21.6 | 21.6 | 21.4 | 20.4 | 19.5 | 17.4 | 16.0 | |
| 16.0 | 16.3 | 16.3 | 16.3 | 16.3 | 16.3 | 16.3 | 15.2 | 13.7 | ||
| 18.0 | 12.6 | 12.6 | 12.6 | 12.6 | 12.6 | 12.6 | 12.6 | 12.2 | ||
| 19.0 | 9.7 | 9.7 | 9.7 | 9.7 | 9.7 | 9.7 | 10.7 | |||
| 23.0 | 6.7 | 6.7 | 6.7 | 6.7 | 6.7 | 9.1 | ||||
| 26.0 | 4.6 | 4.6 | 4.6 | 4.6 | 4.6 | 6.8 | ||||
| 29.0 | 3.0 | 3.0 | 3.0 | 3.0 | 4.5 | |||||
| 35.0 | 1.7 | 1.7 | 1.7 | 3.0 | ||||||
| 38.0 | 0.5 | 0.5 | 1.8 | |||||||
| 41.0 | 0.9 |
150吨汽车起重机性能表(二)
| 吊臂回转至后部及两侧时吊装性能 | ||||||||||
| 工作半径(m) | 吊 臂 长 度 (m) | |||||||||
| 13.9 | 17.7 | 21.3 | 25.0 | 28.7 | 32.3 | 36.0 | 39.6 | 43.1 | 52.8 | |
| 3.0 | 140.0 | |||||||||
| 3.6 | 131.3 | 65.9 | .4 | |||||||
| 4.0 | 122.6 | 65.0 | 63.7 | |||||||
| 4.5 | 109.2 | 65.0 | 63.7 | 56.6 | ||||||
| 5.0 | 100.2 | .9 | 61.2 | 55.4 | ||||||
| 6.0 | 80.3 | .9 | 56.5 | 51.7 | 46.6 | 41.2 | ||||
| 7.0 | 68.9 | 62.0 | 52.5 | 47.2 | 43.9 | 37.8 | 33.1 | 31.5 | ||
| 8.0 | 58.7 | 57.1 | 48.1 | 44.6 | 39.0 | 34.4 | 31.9 | 30.3 | ||
| 9.0 | 49.5 | 49.3 | 44.8 | 40.9 | 35.8 | 31.9 | 29.5 | 27.1 | 27.5 | |
| 10.0 | 43.0 | 41.9 | 41.6 | 35.6 | 33.4 | 29.6 | 27.4 | 25.3 | 24.9 | |
| 12.0 | 31.9 | 31.9 | 31.3 | 27.7 | 24.6 | 22.6 | 22.0 | 21.3 | 17.6 | |
| 14.0 | 24.6 | 24.6 | 24.6 | 24.6 | 21.4 | 20.3 | 19.3 | 18.2 | 15.9 | |
| 16.0 | 18.5 | 18.5 | 18.5 | 18.4 | 17.5 | 16.8 | 15.4 | 13.7 | ||
| 18.0 | 14.7 | 14.7 | 14.7 | 14.7 | 14.7 | 14.4 | 12.5 | 12.0 | ||
| 20.0 | 11.8 | 11.8 | 11.8 | 11.8 | 11.8 | 11.4 | 10.6 | |||
| 23.0 | 8.5 | 8.5 | 8.5 | 8.5 | 8.5 | 9.0 | ||||
| 26.0 | 6.2 | 6.2 | 6.2 | 6.2 | 6.2 | 7.6 | ||||
| 29.0 | 4.4 | 4.3 | 4.2 | 4.2 | 6.1 | |||||
| 32.0 | 2.9 | 2.9 | 2.1 | 4.3 | ||||||
| 35.0 | 1.7 | 1.7 | 2.8 | |||||||
| 38.0 | 0.3 | 2.0 | ||||||||
| 41.0 | 1.2 | |||||||||
| 44.0 | 1.0 | |||||||||
| (注:本表内红字及红字以上栏目的数字为吊臂强度所决定,其下面栏目数字为倾翻力矩决定) | ||||||||||
| 200吨汽车吊车 | ||
LTM1300/1-300t全液压汽车吊机
LTM1300/1-300t全液压汽车吊机主臂额定性能表：
支腿开距=8.85×8.5m、旋转角度=360°、标准配重=87.5t
| 回转半径（m） | 15 | 20.2 | 25.4 | 30.5 | 35.7 | 40.9 | 46.1 | 51.2 | 56.4 | 60 | |
| 3 3.5 | 300 201 | 200 185 | 152 | ||||||||
| 4 4.5 | 131 120 | 120 112 | 116 110 | 114 111 | 95 93 | 76 | |||||
| 5 6 | 113 100 | 104 92 | 105 92 | 104 92 | 91 88 | 75 69 | 60 59 | 49 | |||
| 7 8 | 80 | 82 73 | 82 73 | 82 73 | 81 72 | 57 57 | 48 45 | 39 38.5 | 32 | ||
| 9 10 | 72 61 | 65 59 | 65 59 | 65 59 | 65 58 | 59 | 56 54 | 43 40.5 | 36.5 35 | 31.5 30.5 | 25.5 25.4 |
| 12 14 | 54 49.5 | 53 48.5 | 53 48 | 54 49.5 | 51 48 | 38 36 | 33.5 32.5 | 29.8 28.5 | 24.9 24.5 | ||
| 16 18 | 42
| 41 35 | 40.5 36 | 42.5 36.5 | 42 36 | 31.5 28.3 | 28.9 26 | 26 23.6 | 23 21.4 | ||
| 20 22 | 30.5
| 32 28.3 | 31.5 27.9 | 31 27.2 | 25.8 23.5 | 23.4 21 | 21.5 19.6 | 19.6 18.1 | |||
| 24 26 | 25.1
| 24.7 22.1 | 24.1 21.4 | 21.8 20.4 | 19.2 17.6 | 17.9 16.4 | 16.7 15.4 | ||||
| 28 30 | 19.8
| 19.1 17.1 | 19.2 17.7 | 16.3 15.1 | 15.1 13.9 | 14.3 13.2 | |||||
| 32 34 | 16 13.3 | 16 14.5 | 14 13.2 | 12.8 11.8 | 12.2 11.3 | ||||||
| 36 38 | 13.2 11.3 | 12.4 11.7 | 11.2 10.6 | 10.5 9.8 | |||||||
| 40 42 | 11.2 10.2 | 10 9.4 | 9.1 8.7 | ||||||||
| 44 46 | 8.9 8.5 | 8.3 7.9 | |||||||||
| 48 50 | 7.5 7.1 | ||||||||||
| 52 54 | |||||||||||
| 56 58 | |||||||||||
| 伸1 缩2 工3 况4 （％） | 0 | 0/0 | 0/0/0 | 46/0/0 | 46/0/0 | 92/46/0 | 92/46 | 92/46 | 92 | 100 | |
| 0 | 46/0 | 46/0/0 | 46/0/0 | 46/46/0 | 46/92/92 | 92/92/92 | 92/92 | 92 | 100 | ||
| 0 | 0/0 | 0/46/0 | 46/46/92 | 46/46/46 | 46/46/92 | 46/92/92 | 92/92 | 92 | 100 | ||
| 0 | 0/46 | 0/46/92 | 0/46/46 | 0/46/46 | 46/46/46 | 46/46/92 | 46/92 | 92 | 100 | ||
主臂额定性能表1：支腿开距=10×9.6m、旋转角度=360°、标准配重=135t。
| 回转半径（m） | 主臂长度（m） | 回转半径（m） | |||||||
| 16.1 | 21.3 | 26.5 | 31.7 | 36.9 | 42.1 | ||||
| 3 3.5 | 500 400 | 500 400 | 500 400 | 262 | 3 3.5 | ||||
| 4 4.5 | 325 262 | 325 262 | 325 261 | 262 259 | 248 239 | 4 4.5 | |||
| 5 6 | 261 231 | 255 226 | 245 216 | 243 214 | 229 208 | 183 168 | 145 | 5 6 | |
| 7 8 | 206 186 | 202 182 | 192 173 | 190 170 | 190 170 | 156 145 | 133 123 | 116 107 | 7 8 |
| 9 10 | 170 155 | 162 145 | 156 141 | 153 138 | 153 138 | 134 124 | 114 106 | 100 94 | 9 10 |
| 12 14 | 128 107 | 119 100 | 117 99 | 114 97 | 114 97 | 107 93 | 92 80 | 83 73 | 12 14 |
| 16 18 | 82 71 | 82 71 | 83 71 | 71 65 | 63 55 | 16 18 | |||
| 20 22 | 56 | 61 53 | 62 54 | 58 53 | 49.5 45 | 20 22 | |||
| 24 26 | 47 | 47.5 42.5 | 46 40.5 | 40.5 36.5 | 24 26 | ||||
| 28 30 | 37.5 32.5 | 36 32 | 33.5 31 | 28 30 | |||||
| 32 34 | 28.3 25.3 | 28.5 26.6 | 32 34 | ||||||
| 36 38 | 24.2 21.7 | 36 38 | |||||||
| 40 | 19.4 | 40 | |||||||
主臂额定性能表2：支腿开距=10×9.6m、旋转角度=360°、标准配重=135t。
| 回转半径（m） | 主臂长度（m） | 回转半径（m） | |||||||
| 47.3 | 52.5 | 57.7 | 62.9 | 68.1 | 73.4 | 78.6 | 84 | ||
| 8 9 | 93 87 | 73 | 8 9 | ||||||
| 10 12 | 81 72 | 69 63 | 60 54 | 46.5 | 41 | 10 12 | |||
| 14 16 | 63 57 | 57 52 | 49.5 45 | 43 39 | 38 35 | 33.5 31 | 27.4 | 20.9 | 14 16 |
| 18 20 | 50 45 | 46 41.5 | 41.5 38 | 36 33 | 32.5 30 | 28.8 26.8 | 25.8 24.2 | 19.5 18.2 | 18 20 |
| 22 24 | 40 36.5 | 37.5 34 | 35 32 | 30.5 28.2 | 27.8 25.9 | 24.9 23.2 | 22.6 21.1 | 16.8 15.6 | 22 24 |
| 26 28 | 34 31.5 | 30.5 28.1 | 28.9 26.4 | 25.9 24 | 24.1 22.5 | 21.6 20.2 | 19.8 18.6 | 14.4 13.4 | 26 28 |
| 30 32 | 28.9 26.6 | 26 24 | 24.8 23 | 22.2 20.6 | 20.7 19 | 18.6 17.3 | 17.4 16.3 | 12.4 11.4 | 30 32 |
| 34 36 | 24.5 22.5 | 22.2 20.5 | 21.4 19.8 | 19 17.4 | 17.5 16.1 | 16.1 15 | 15 13.9 | 10.2 9.2 | 34 36 |
| 38 40 | 20.3 18 | 18.9 17.4 | 18.3 16.9 | 15.8 14.2 | 15 14 | 13.9 12.9 | 12.9 12 | 8.4 7.6 | 38 40 |
| 42 44 | 16.1 14.3 | 15.9 14.5 | 15.6 14.3 | 13.2 12.1 | 13 11.9 | 12 11 | 11.2 10.3 | 6.9 6.2 | 42 44 |
| 46 48 | 9.2 | 13.2 11.8 | 13.1 11.9 | 11.2 10.3 | 10.9 9.9 | 10.1 9.3 | 9.5 8.8 | 5.5 4.8 | 46 48 |
| 50 52 | 8.8 | 10.8 9.6 | 9.4 8.5 | 8.9 8.2 | 8.7 8.1 | 8.1 7.6 | 4.2 3.8 | 50 52 | |
| 54 56 | 8.5 5.2 | 7.7 6.9 | 7.6 7 | 7.5 6.9 | 7.2 6.7 | 3.5 3.2 | 54 56 | ||
| 58 60 | 6.2 5.4 | 6.4 5.8 | 6.4 5.8 | 6.3 5.9 | 2.8 2.5 | 58 60 | |||
| 62 | 5.3 4.7 | 5.3 4.8 | 5.4 5 | 2.2 1.9 | 62 | ||||
| 66 68 | 3.2 | 4.3 3.8 | 4.9 4.1 | 66 68 | |||||
| 70 72 | 3.4 | 3.7 3.3 | 70 72 | ||||||
| 74 | 2.9 | 74 | |||||||
Copyright © 2019-2025 51dongshi.net 版权所有
违法及侵权请联系：TEL:177 7030 7066 E-MAIL:11247931@qq.com 本站由北京市万商天勤律师事务所王兴未律师提供法律服务
