MOC3052

* Isolation voltage between input and output V iso : 5,000V rms * 6pin DIP photocoupler, triac driver output

* High repetitive peak off-state voltage V DRM : Min. 600V

* High critical rate of rise of off-state voltage

( dv/dt : MIN. 1000V / µs )

* Dual-in-line package :

MOC3052

* Wide lead spacing package :

MOC3052M

* Surface mounting package :

MOC3052S

* Tape and reel packaging :

MOC3052S-TA1

* UL approved ( No. E1138 )

* CSA approved ( No. CA91533-1 )

* FIMKO approved ( No. 15469 )

* NEMKO approved ( No. P0******* )

* DEMKO approved ( No. 309968-01 )

* SEMKO approved ( No. 0032019/01-11 )

* VDE approved (No. 094722 )

APPLICATION

* Incandescent Lamp Dimmers

* Interfacing Microprocessors to 115 and 240 Vac Peripherals * Lamp Ballasts

* Motor Controls

* Solid State Relays

* Static AC Power Switch

* Solenoid / Valve Controls

* Temperature Controls

ABSOLUTE MAXIMUM RATING

( Ta = 25°C ) PARAMETER SYMBOL RATING UNIT

Forward Current I F50 mA

Reverse Voltage V R 6 V INPUT

Power Dissipation P D100 mW

Off-State Output Terminal Voltage V DRM600 V

Peak Repetitive Surge Current ( PW=100µs, 120pps ) I TSM 1 A

OUTPUT

Collector Power Dissipation P C300 mW Total Power Dissipation P tot330 mW *1 Isolation Voltage V iso5,000 Vrms Ambient Operating Temperature Range T A-40 ~ +100 °C Storage Temperature Range T stg-55 ~ +150 °C *2 Soldering Temperature T L260 °C

*1. AC For 1 Minute, R.H. = 40 ~ 60%

Isolation voltage shall be measured using the following method.

(1) Short between anode and cathode on the primary side and between collector,

emitter on the secondary side.

(2) The isolation voltage tester with zero-cross circuit shall be used.

(3) The waveform of applied voltage shall be a sine wave.

*2. For 10 SecondsELECTRICAL - OPTICAL CHARACTERISTICS

( Ta = 25°C ) PARAMETER SYMBOL MIN. TYP. MAX. UNIT CONDITIONS Forward Voltage V F — 1.2 1.4 V I F=20mA INPUT

Reverse Current I R — 0.05 10 µA V R=6V

*1 Peak Blocking Current, Either

Direction

I DRM— — 100 nA V DRM = 600V

Peak On-State Voltage, Either Direction V TM— — 3.0 V I TM=100 mA Peak

OUTPUT

*2 Critical rate of Rise of

Off-State Voltage

dv/dt 1000 — — V/µs

*3

Led Trigger Current, Current

Required to Latch Output, Either Direction I FT— — 10 mA

Main Terminal

Voltage = 3V

COUPLED

Holding Current, Either

Direction

I H— 400 — µA

*1 Test voltage must be applied within dv/dt rating.

*2 This is static dv/dt. Commutating dv/dt is a function of the load-driving thyristor(s) only.

*3 All devices are guaranteed to trigger at an I F value less than or equal to max I FT. Therefore, recommended operating I F lies between max 10mA for MOC3052 and absolute max I F (50mA)

Notes:

- Lite-On is continually improving the quality, reliability, function or design and

Lite-On reserves the right to make changes without further notices.

- The products shown in this publication are designed for the general use in electronic

applications such as office automation equipment, communications devices,

audio/visual equipment, electrical application and instrumentation.

- For equipment/devices where high reliability or safety is required, such as space

applications, nuclear power control equipment, medical equipment, etc, please

contact our sales representatives.

- When requiring a device for any ”specific” application, please contact our sales in

advice.

- If there are any questions about the contents of this publication, please contact us at

your convenience.

-The contents described herein are subject to change without prior notice.

-No contacting on pin 5.

-Inhibit immersing unit’s body in solder paste.

Part No. :MOC3052 SERIES Page :9 of 9 BNS-OD-C131/A4