NCE3401

Package Marking And Ordering Information

Device Marking Device Device Package Reel Size Tape width Quantity

3401 NCE3401 SOT-23 Ø180mm8 mm 3000 units

Absolute Maximum Ratings (TA=25℃unless otherwise noted)

Unit

Limit

Parameter Symbol

Drain-Source Voltage V DS-30 V

Gate-Source Voltage V GS±12 V

Drain Current-Continuous I D-4.2 A

Drain Current-Pulsed (Note 1) I DM-30 A

Maximum Power Dissipation P D 1.25 W

Operating Junction and Storage Temperature Range T J,T STG-55 To 150 ℃

Thermal Characteristic

℃

Thermal Resistance,Junction-to-Ambient (Note 2)RθJA100/W

Electrical Characteristics (TA=25℃unless otherwise noted)

Parameter Symbol Condition Min Typ Max Unit

Off Characteristics

Drain-Source Breakdown Voltage BV DSS V GS=0V I D=-250μA -30 V

μA

=0V -1

Zero Gate Voltage Drain Current I DSS V DS=-24V,V GS

Gate-Body Leakage Current I GSS V GS =±12V,V DS =0V ±100 nA On Characteristics (Note 3) Gate Threshold Voltage

V GS(th) V DS =V GS ,I D =-250μA -0.7 -1.3 V V GS =-10V, I D =-4.2A 48 60 m Ω Drain-Source On-State Resistance R DS(ON) V GS =-4.5V, I D =-4A 62 70 m Ω Forward Transconductance g FS

V DS =-5V,I D =-4.2A 10 S

Dynamic Characteristics (Note4) Input Capacitance C lss 950 PF Output Capacitance

C oss 115 PF

Reverse Transfer Capacitance C rss

V DS =-15V,V GS =0V,

F=1.0MHz

75 PF Switching Characteristics (Note 4) Turn-on Delay Time t d(on) 7 nS

Turn-on Rise Time t r 3 nS Turn-Off Delay Time t d(off) 30 nS

Turn-Off Fall Time t f

V DD =-15V,I D =-3.2A V GS =-10V,R GEN =6Ω 12 nS

Total Gate Charge Q g 9.5 nC Gate-Source Charge Q gs 2 nC

Gate-Drain Charge

Q gd V DS =-15V,I D =-4A,V GS =-4.5V 3 nC

Drain-Source Diode Characteristics Diode Forward Voltage (Note 3)

V SD

V GS =0V,I S =-1A

-1.2 V

Notes:

1. Repetitive Rating: Pulse width limited by maximum junction temperature.

2. Surface Mounted on FR4 Board, t ≤ 10 sec.

3. Pulse Test: Pulse Width ≤ 300μs, Duty Cycle ≤ 2%.

4. Guaranteed by design, not subject to production

TYPICAL ELECTRICAL AND THERMAL CHARACTERISTICS

Figure 1:Switching Test Circuit

T J -Junction Temperature(℃)

Figure 3 Power Dissipation

Vds Drain-Source Voltage (V)

Figure 5 Output CHARACTERISTICS

V IN

V t

Figure 2:Switching Waveforms

T J -Junction Temperature(℃)

Figure 4 Drain Current

I D - Drain Current (A)

Figure 6 Drain-Source On-Resistance

P D P o w e r (W )

I D - D r a i n C u r r e n t (A ）

R d s o n O n -R e s i s t a n c e (m Ω)

I D - D r a i n C u r r e n t (A )

Vgs Gate-Source Voltage (V)

Figure 7 Transfer Characteristics

Vgs Gate-Source Voltage (V)

Figure 9 Rdson vs Vgs

Qg Gate Charge (nC)

Figure 11 Gate Charge

T J -Junction Temperature(℃)

Figure 8 Drain-Source On-Resistance

Vds Drain-Source Voltage (V)

Figure 10 Capacitance vs Vds

Vsd Source-Drain Voltage (V)

Figure 12 Source- Drain Diode Forward

I D - D r a i n C u r r e n t (A )

R d s o n O n -R e s i s t a n c e (m Ω)

V g s G a t e -S o u r c e V o l t a g e (V )

N o r m a l i z e d O n -R e s i s t a n c e

C C a p a c i t a n c e (p F )

I s - R e v e r s e D r a i n C u r r e n t (A )

NCE3401

Pb Free Product

http://www.ncepower.com

Vds Drain-Source Voltage (V)

Figure 13 Safe Operation

Area

Square Wave Pluse Duration(sec)

Figure 14 Normalized Maximum Transient Thermal Impedance

r (t ),N o r m a l i z e d E f f e c t i v e

T r a n s i e n t T h e r m a l I m p e d a n c e

I D - D r a i n C u r r e n t (A )

NCE3401

Pb Free Product

http://www.ncepower.com

TYPICAL ELECTRICAL CHARACTERISTICS

Vout

Figure 1:Switching Test Circuit

V IN

V t

Figure 2:Switching Waveforms

SOT-23 PACKAGE INFORMATION

Dimensions in Millimeters (UNIT:mm)

Dimensions in Millimeters

Symbol

MIN. MAX.

A 0.900 1.150

A1 0.000 0.100

A2 0.900 1.050

b 0.300 0.500

c 0.080 0.150

D 2.800 3.000

E 1.200 1.400

E1 2.250 2.550

e 0.950TYP

e1 1.800 2.000

L 0.550REF

L1 0.300 0.500

θ 0° 8°

NOTES

1. All dimensions are in millimeters.

2. Tolerance ±0.10mm (4 mil) unless otherwise specified

3. Package body sizes exclude mold flash and gate burrs. Mold flash at the non-lead sides should be less than 5 mils.

4. Dimension L is measured in gauge plane.

5. Controlling dimension is millimeter, converted inch dimensions are not necessarily exact.

ATTENTION:

■Any and all NCE power products described or contained herein do not have specifications that can handle applications that require extremely high levels of reliability, such as life-support systems, aircraft's control systems, or other applications whose failure can be reasonably expected to result in serious physical and/or material damage. Consult with your NCE power representative nearest you before using any NCE power products described or contained herein in such applications.

■ NCE power assumes no responsibility for equipment failures that result from using products at values that exceed, even momentarily, rated values (such as maximum ratings, operating condition ranges, or other parameters) listed in products specifications of any and all NCE power products described or contained herein.

■Specifications of any and all NCE power products described or contained herein stipulate the performance, characteristics, and functions of the described products in the independent state, and are not guarantees of the performance, characteristics, and functions of the described products as mounted in the customer’s products or equipment. To verify symptoms and states that cannot be evaluated in an independent device, the customer should always evaluate and test devices mounted in the customer’s products or equipment.

■ NCE power Semiconductor CO.,LTD. strives to supply high-quality high-reliability products. However, any and all semiconductor products fail with some probability. It is possible that these probabilistic failures could give rise to accidents or events that could endanger human lives, that could give rise to smoke or fire, or that could cause damage to other property. When designing equipment, adopt safety measures so that these kinds of accidents or events cannot occur. Such measures include but are not limited to protective circuits and error prevention circuits for safe design, redundant design, and structural design.

■ In the event that any or all NCE power products(including technical data, services) described or contained herein are controlled under any of applicable local export control laws and regulations, such products must not be exported without obtaining the export license from the authorities concerned in accordance with the above law.

■No part of this publication may be reproduced or transmitted in any form or by any means, electronic or mechanical, including photocopying and recording, or any information storage or retrieval system, or otherwise, without the prior written permission of NCE power Semiconductor CO.,LTD.

■Information (including circuit diagrams and circuit parameters) herein is for example only ; it is not guaranteed for volume production. NCE power believes information herein is accurate and reliable, but no guarantees are made or implied regarding its use or any infringements of intellectual property rights or other rights of third parties.

■ Any and all information described or contained herein are subject to change without notice due to product/technology improvement, etc. When designing equipment, refer to the "Delivery Specification" for the NCE power product that you intend to use.

■This catalog provides information as of Sep 2010. Specifications and information herein are subject to change without notice.