约克螺杆机控制线路图原版)

PRODUCT DRAWING

YORK INTERNATIONAL CORPORATION

P .O. Box 1592, YORK, PA 17405

CONTRACTOR _______________________PURCHASER ____________________________________________ORDER NO.__________________________JOB NAME _______________________________________________YORK CONTRACT NO._________________LOCATION _______________________________________________YORK ORDER NO.____________________

ENGINEER ______________________________________________

REFERENCE

DA TE ________

APPROVAL DA TE ________

CONSTRUCTION DATE ________

Supersedes: Nothing WIRING DIAGRAM

MILLENNIUM Y S (STYLE C) ROTARY SCREW CHILLER

MICROCOMPUTER CONTROL CENTER WITH ELECTRO-MECHANICAL STARTER

JOB DATA:

CHILLER MODEL NO. YS _________________NO. OF UNITS __________________________

COMPRESSOR MOTOR ________________VOLTS, 3-PHASE,______________________________H Z

REMARKS:_____________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________

FORM 160.47-PW1 (7)

REF. 035-09973-000, REV D

(Cont d. on pages 3 & 4)

LD02399

2 YORK INTERNATIONAL

FORM 160.47-PW1

3

YORK INTERNATIONAL

ELEMENTARY DIAGRAM

LD02400

LD02401

TIMING DIAGRAM

4

YORK INTERNATIONAL

FORM 160.47-PW1

5

YORK INTERNATIONAL

LD02403

ELEMENTARY DIAGRAM (Cont d.)

1.This wiring diagram describes the standard electronic

control scheme for use with an Electro-Mechanical Starter. For details of standard modifications (by oth-ers), refer to Product Drawing Form 160.47-PW5.

2.Field wiring to be in accordance with the National

Electrical Code as well as all other applicable codes and specifications. See Product Drawing Form 160.47-PW3 for field wiring connections.

3.Numbers along the left side of diagram are line iden-

tification numbers. The numbers along the right side indicate the line number location of relay contacts.

An underlined contact location signifies a normally closed contact.

4.Main control panel Class 1 field wiring terminal con-

nection points are indicated by numbers within a rect-angle, i.e. 15 . Main control panel factory wiring terminal connection points are indicated by numbers within a triangle, i.e. 5 . Component terminal markings are indicated by numbers within a circle, i.e.

C1 . Numbers adjacent to circuit lines are the circuit identification numbers.

5.To cycle on and off automatically with contacts other

than those shown, install a cycling device between terminals 1 & 13 (line 27) (see Note 9). If a cycling device is installed, jumper must be removed between terminals 1 & 13 .

6.Compressor motor starter with starter interlock con-

tacts (rated 0.2 amps @ 120 volts A.C.) must be per Form 160.47-PW7. Control panel shall be grounded.

7.Units installed in Canada must have a field supplied

CSA approved 30 amp disconnect switch and a 15 amp dual element fuse mounted external to control panel for 115 volt control supply.

8.To stop unit and not permit it to start again, install a

stop device between terminals 1 & 8 (line 23) (see Note 9). A Remote start-stop switch may be

connected to terminals 1 , 7 & 8 (lines 22 and

23) (see Note 9). Remote start-stop switch (line 22)

is operative only in the remote operating mode.

9.Device contact rating to be 5 miliamperes at 115 volts

A.C.

10.Contact rating is 5A resistive @ 120 volts A.C. or

240 volts A.C.

11.To check motor rotation on initial start-up, install mo-

mentary switch between terminals 24 & 25 (line

35). Depress start switch, after approx. 30 seconds,

jog motor with momentary switch. When proper rota-tion is obtained, replace momentary switch with jumper. Switch must have a minimum contact rating of 2 FLA, 10 LRA at 115 volts A.C.

12.Solid state motor overload (CM) is set to trip at 105%

FLA. During momentary power interruption (power fault), contact also opens for 1 second.

13.For high and low voltage units, the factory supplied

jumper between 1 & 53 must be removed when Electro-Mechanical starter overloads and/or safety devices are used. For high voltage (2300-4160) UL and CSA approved units only, electro-mechanical compressor motor starter overloads (normally closed) must be connected between 1 & 53 .

14.Contact rating is 5 amps resistive @ 250 volts A.C.

& 30 volts D.C., 2 amp inductive (0.4 PF) @ 250 volts A.C. & 30 volts D.C.

15.Each 115VAC field-connected inductive load, i.e. re-

lay coil, motor starter coil, etc. shall have a transient suppressor wired in parallel with its coil, physically located at the coil. Spare transient suppressors and control circuit fuses are supplied in a bag attached to the top of the hinged panel.

16.Low oil pressure (LOP) safety shutdown occurs when

oil pressure evaporator pressure differential is less that 15 psi following a 3 minute bypass at compres-sor start.

LEGEND

LD02402

6 YORK INTERNATIONAL

FORM 160.47-PW1

7YORK INTERNATIONAL PRESSURE TEMPERATURE CHART

LD02404

* Function provided by condenser transducer

8

YORK INTERNATIONAL

FORM 160.47-PW1

9

YORK INTERNATIONAL CONNECTION DIAGRAM LD02405

10

YORK INTERNATIONAL

FORM 160.47-PW1

11

YORK INTERNATIONAL LD02406

CONNECTION DIAGRAM (Cont d)

P.O.Box1592,YORK,Pennsylvania USA17405-1592Subject to change without notice.Printed in USA Copyright©by YORK International Corporation1997ALL RIGHTS RESERVED Form160.47-PW1(7)

Supersedes:Nothing